Digital clock thermostat
ref. 56254
Thermostat has been designed to offer you comfort and energy
savings. It allows you to program and adjust your heating or air
conditioning according to 3 temperature levels:
- Comfort temperature: this is the temperature for your hours
of presence.
- Reduced temperature: this is the temperature for your brief
absences or during the night.
- Frost-protection temperature: this is the minimum tempe-
rature for long absences. It protects your dwelling from the risk
of frost.
These 3 pre-recorded programs and a blank program will allow
you to adapt your heating each day to your life style.
This instruction leaflet introduces you to the different functions of
thermostat.
Inserting or re-inserting the
batteries
Thermostat is equipped with a warning light to indi-
cate when the batteries need replacing. As soon as
this indicator lights up at the bottom right-hand side
of the display panel, replace the batteries (use two
1.5V UR6 alkaline batteries - life is approximately
18 months): thermostat remains programmed for
60 seconds while batteries are being replaced.
Before beginning the program-
!
ming of the device, please slide
cover down and press RESET
with the tip of a pen.
Setting to current time and day
- You are putting the device into
operation for the first time.
- You have just pressed the
RESET button (see above).
- 12:00 appears and the pointer
L
flashes under day 1.
u
Auto Manu
1
2
3
4
5
+
-
DAYS
PROG
OK
1-7
P1-P4
Set the time using the +/– buttons (the numbers
run off more quickly when the button is pressed
continuously).
Set the current day by pressing several times on
the DAYS 1-7 button.A pointer
the corresponding day (1=Monday, 2=Tuesday,
3=Wednesday, etc.)
Validate with the OK button.
If you wish to change the time or the day:
press the MODE button until the pointer
appears under the clock sign and continue as above
for points ,
and .
+/– buttons for
adjusting settings
Indicator for
temperature level
"comfort"
or "reduced"
(1=Monday, 2=Tuesday....
Temperature setting
Comfort and reduced temperatures are pre-set:
comfort = 20°C, reduced = 16°C
+
-
DAYS
1-7
Modification of Comfort temperature
Press the comfort button.
Modify the temperature with the +/– buttons.
Validate with OK.
Modification of Reduced temperature
Press the reduced button.
Modify the temperature with the +/– buttons.
Validate with OK.
22 23 24
Programming
You can program your week according to 4
Res
program settings:
P1, P2, P3 : are pre-recorded and cannot be modified.
P4 :
1
2
3
4
P1 = Comfort temperature from 6 a.m. till 11 p.m.
Reduced temperature from 11 p.m till 6 a.m.
The standard allocation of P1 is to 7 days of the week.
If this corresponds to your life style, stay in automatic
mode. Otherwise, continue.
6
7
MODE
MODE
0
1
2
3
4
P2 = Comfort temperature from 6 a.m.till 8.30 p.m.
and from 4.30 p.m. till 11 p.m. Reduced tempe-
rature from 8.30 a.m. till 4.30 p.m. and from 11
Res
p.m. till 6 a.m.
0
1
2
3
4
P3 = Comfort temperature from 6 a.m. till 8.30
p.m. from 11.30 a.m. till 1.30 p.m. and from
4.30 p.m. till 11 p.m. Reduced temperature
from 8.30 a.m. till 11.30 a.m.from 1.30 p.m.
L
appears under
till 4.30 p.m. and from 11 p.m. till 6 a.m.
0
1
2
3
4
P4 = Blank program allowing you to create up to
L
12 comfort temperature periods and 12
reduced periods for each day of the week.
"Reduced"
indicating day
temperature
"Comfort"
temperature
Auto Manu
+
¡c
¡c
-
0
1
2
3
4
5
current
DAYS
PROG
1-7
P1-P4
Days of the
P1 to P4
Comfort
week selection
programme
temperature
selection
setting
7=Sunday)
Auto Manu
1
2
3
4
5
6
7
c
°c
°c
c
PROG
OK
P1-P4
is blank and allows you to create a
personalized program varying accor-
ding to the day of the week.
5
6
7
8
9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
5
6
7
8
9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
5
6
7
8
9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
3
3
Warning light
Pointer
Ambient
to indicate
temperature
battery wear
of the week
1
2
3
4
5
6
7
¡c
timer
days
6
7
8
9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
OK
Reduced
Validation
temperature
setting
Selection of an existing P1, P2 or P3
programme for a day of the week (in
programming mode all modifications are
automatically validated).
Example - P2 for Wednesday
Auto Manu
1
+
°c
MODE
°c
-
0
1
2
3
4
5
6
7
8
9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
DAYS
PROG
Res
1-7
P1-P4
Press the PROG P1-P4 button to go into
programming mode.
The n° of the program assigned to the day flashes
on the right-hand side of the display panel.
Press the DAYS 1-7 until the pointer
under the day you wish to program (Wednesday in
our example).
Press the PROG P1-P4 button until the P2 pro-
gram number flashes in the right side of the screen.
Press the OK button to validate.The following day
PROG
P1-P4
is automatically proposed.
Creating a P4 program
A 24-hour profile composed of 48 thermometers at
the bottom of the display panel allows your
rogramme composition to be easily viewed.
half-empty thermometer corresponds to
30 minutes at reduced temperature.
A full thermometer corresponds to
30 minutes at comfort temperature.
Example - programming 3 temperature periods for
Friday: 6 a.m. till 8 a.m., noon till 2 p.m. and 6 p.m.
till 10 p.m.
Auto Manu
1
+
°c
°c
-
0
1
2
3
4
5
6
7
8
0
1
DAYS
PROG
1-7
P1-P4
From the AUTO mode press the PROG P1-P4
button.
Press the DAYS 1-7 button until a pointer
appears under the day you wish to program (Friday
in our example).
Press the PROG P1-P4 button until the P4
program number flashes in the right side of the
screen.Your display panel indicates time as 0h00
and the first thermometer flashes on the 24-hour
profile.
Heating
start-up
indicator
Mode
selection
Prolonged
absence
MODE
(holidays)
Viewing of
"comfort" and
"economical"
periods"
Res
RESET
2
3
4
5
6
7
MODE
OK
Res
L
appears
2
3
4
5
6
7
MODE
9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
OK
Res
L