JUNO 56RLSRETROKIT Instrucciones De Instalación

IMPORTANT: For your safety, read and understand these instructions and the instructions that ship with the 6RLS fixtures completely
before starting installation. Before wiring to power supply, turn off electricity at the fuse or circuit breaker box.
THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON
FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.
NOTE: Before attempting installation of any lighting fixture, check your local electrical building code. This code sets the wiring
and installation requirements for your locality and should be understood before starting your work.
WARNING – Risk of fire or electric shock.
- LED Retrofit Kit installation requires knowledge of luminaires electrical systems. If not qualified, do not attempt installation.
Contact a qualified electrician.
- Install this kit only in the luminaires that have the construction features and dimensions outlined in these instructions, and where
the input rating of the retrofit kit does not exceed the input rating of the luminaire.
- Do not make or alter any open holes in an enclosure of wiring or electrical components during kit installation.
- To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or other sharp objects.
AVERTISSEMENT – Risque d'incendie ou d'électrocution.
- L'installation de l'ensemble de modification de LED exige une connaissance des circuits électriques de luminaires.
Si vous n'êtes pas qualifié, n'essayez de procéder au montage. Mettez-vous en rapport avec un électricien qualifié.
- Ne montez cette trousse que dans les luminaires possédant les caractéristiques et dimensions décrites dans ce mode d'emploi,
et où la tension nominale d'entrée de la trousse de conversion n'est pas supérieure à celle du luminaire.
- Ne pratiquez pas ou ne modifiez pas de trous ouverts dans une enceinte de câblage ou des composants électriques lors
de l'installation de l'ensemble.
- Afin d'éviter tout endommagement ou abrasion du câblage, évitez tout contact avec les arêtes de la tôle ou d'autres
objets tranchants.
SAVE THESE INSTRUCTIONS
Description: This accessory kit allows Juno 6RLS series surface mount light fixtures to be mounted to most 5" and 6" type IC or
Non-IC recessed incandescent light fixtures as a retrofit trim. The accessory kit consists of the following: medium base socket
adapter, pluggable electrical connector, and mounting springs.
Compatibility: When used with 56RLSRETROKIT, Juno 6RLS series light fixtures are designed to work with most standard UL listed
recessed incandescent housings with a medium base socket. Compatible size ranges for housings can be determined by measuring
the diameter and height as shown in Figure 1, and referring to the height and diameter chart. Housing construction features vary,
so the chart should be used as a guideline. Actual installation is the best method of determining compatibility.
Internal
Diameter
Figure 1
Products are suitable for installation in damp
locations. Products are suitable for installation
in wet locations (indoor covered ceilings
only) when sealed to mounting surface with a
waterproof sealant such as silicone caulk (see
Figure 2).
These products have integral LED electronics.
Replace entire fixture in the event of failure.
1300 S. Wolf Road • Des Plaines, IL 60018 • Phone 800-323-5068 • Visit us at www.acuitybrands.com/juno-recessed
©2017 Acuity Brands Lighting, Inc
INSTALLATION INSTRUCTIONS
Internal
Height
Internal Diameter
Internal Height
Minimum lamp compartment: 78 in
SEE
CHART
Seal fixture to surface around
this entire edge.
Figure 2
Rev 3/17 P6101
For 56RLSRETROKIT Accessory Kit
5" and 6"
Recessed Housings
5" - 7"
4" min.
3 (1278 cm 3 )
1 of 2