Classic smart LEARNING Manual De Instrucciones página 6

GB
seconds.
If your TV has a picture function key and uses On-Screen-Display (OSD)
to show the selected picture function:
Press the PICTURE key on smart LEARNING.
Picture Select command will be transmitted as on your original remote
control.
If your TV allows you to control picture settings by Menu:
Press MENU key on smart LEARNING.
Menu command will be transmitted as on our original remote control.
H) HOW TO ADJUST TREBLE, BASS AND BALANCE ON YOUR TV.
Only available in TV device mode.
If your TV has separate +/- (up/down) keys for each function:
1) Press the blue SOUND key on smart LEARNING to step through the
SOUND functions TREBLE > BASS > BALANCE until the red LED
above the desired blue symbol is on.
2) Within 5 seconds press the < (-) or > (+) key to adjust the setting.
3) After adjustment the handset will revert to normal operation within 5
seconds.
If your TV has a sound function key and uses On-Screen-Display (OSD)
to show the selected sound function:
Press the blue SOUND key on smart LEARNING.
Sound Select command will be transmitted as on your original remote
control.
If your TV allows you to control sound settings by Menu:
Press MENU key on smart LEARNING.
Menu command will be transmitted as on your original remote control.
I) VOLUME PUNCH THROUGH.
You can programme the smart LEARNING to control the TV volume even
when it is switched to another device mode.
1) Press and hold down the required device key on the smart LEARNING
(e.g. VCR) and at the same time press and hold down the VOL up key.
Keep both keys pressed down for approximately two seconds until the
indicator light on the device key being held down lights and remains on.
Release both keys.
2) Press and release the TV device key
3) The indicator will blink twice.
The volume/mute keys will now still control the TV even when the
smart LEARNING is switched to the selected device mode.
Repeat steps 1 and 2 selecting SAT/STB or DVD as required.
J) SWITCH OFF VOLUME PUNCH THROUGH
Press and hold down the required device key on the smart LEARNING (e.g.
VCR) and at the same time press and hold down the VOL down key. Keep
both keys pressed down for approximately two seconds until the indicator light
on the device key being held down blinks twice.
Please note that when the smart LEARNING is in the programming mode, if
no key is pressed within 20 seconds the handset will return to normal
operation mode.
K) LEARNING MODE
The smart LEARNING has a highly sophisticated learning feature included.
It allows smart LEARNING to learn in and store up to 50 commands in each
of the 6 device levels. Learned commands are held in a Flash-Memory and
10
will not be lost when the batteries are exhausted or removed.
In order to learn infrared signals with toggle bits smart LEARNING will
always ask you to send each command twice.
1) Place the smart LEARNING and the original remote control (Source)
head to head at a distance of approx. 5 cm.
2) Press and hold down the required device key on the smart LEARNING
(e.g. TV) and at the same time press and hold down the REC key. Keep
both keys pressed down for approximately two seconds until the red light
on the device key being held down and the orange "LEARN" indicator
light both light and remain on. Release both keys.
3) Press the target key on the smart LEARNING.
The "LEARN" LED blinks once orange and the device LED switches
off. smart LEARNING is now ready to learn.
4) Press the source key on your original remote control for about 1 sec.
5) When the signal is received correctly the "LEARN" indicator turns to
green for 2 sec and then returns to orange again.
6) Press the same source key a second time. If the code has been learned
correctly the indicator will blink twice green and then changes to orange.
At the same time the device key lights up again and smart LEARNING
is ready to learn the next command.
7) Press the next target key and continue with step 4.
8) If the command is not learned correctly the "LEARN" indicator blinks
twice red and then turns to orange and the device key lights up again.
9) In this case start again with step 3)
10) Press the device key to leave the LEARN mode.
Red light in device key turns off and learned commands are stored.
If LEARNING procedure is not completed and no key is pressed within
20 seconds smart LEARNING returns to normal operation mode.
L) ERASE ALL LEARNED COMMANDS OF 1 DEVICE
Press and hold down the required device key on the smart LEARNING for
the mode in which you want to erase all of the learned commands. At the
same time press and hold down the STOP key for 5 seconds.
The device key lights up red and the "LEARN" indicator orange.
After 5 seconds the "LEARN" indicator blinks green, orange, green, orange
and turns off. Selected device key learned commands are erased completely.
M) ERASE learned command on 1 KEY ONLY
1) Press and hold down the required device key on the smart LEARNING
for the mode in which you want to erase one of the learned commands.
At the same time press and hold down the STOP key for 2 seconds.
The device key lights up red and the "LEARN" indicator orange.
2) Press the key you want to erase.
The "LEARN" indicator blinks green twice and then returns to orange.
3) If you want to erase the command on another key repeat step 2. If you
do not want
to erase any other commands go to step 4.
4) Press device key for confirmation.
The "LEARN" Indicator blinks orange twice and then goes off. The
device key light goes off.
If ERASE procedure is not completed and no key is pressed within 20
seconds smart LEARNING returns to normal operation mode.
N) LOW BATTERY WARNING.
Whenever the batteries in the smart LEARNING fall to a low level all the
device indicators will blink 3 times each time the Power button is pressed.
This indicates that you should replace the batteries as soon as possible.
smart LEARNING may stop operation but will never lose installed or learned
commands because of its flash-memory.
GB
11