Sony XBA-2VP Manual De Instrucciones

Stereo Headset
Operating Instructions
Manual de instrucciones
XBA-2VP

Conversion cord

2
1

1
Earbud
Tactile dot
3


Sectional View
Colored parts
Pressure-relieving
urethane cushion



English
Stereo headset
WARNING
To reduce the risk of fire or electric shock, do not expose this apparatus to rain
or moisture.
To reduce the risk of electrical shock, do not open the cabinet. Refer servicing to
qualified personnel only.
You are cautioned that any changes or modifications not expressly approved in this
manual could void your authority to operate this equipment.
Features
4-418-201-31(1)
©2011 Sony Corporation
 Earbuds with remote controller for smartphone
Printed in Thailand
Easy-to-use remote control (for smartphone).
 Handsfree headset with microphone
 Newly developed Dual Balanced Armature driver unit
Newly developed micro-size driver unit (full-range + woofer) reproduces smooth and
clear vocal, with rich and powerful bass.
 Newly developed Double Layered Housing
Magnesium inner housing holds the driver units rigidly for smooth sound response.
Special ABS plastic outer housing prevents unwanted vibration for clear mid-high
range.
 Noise-blocking design
Noise-blocking design attenuates ambient noise and sound leakage.
 Super-small body
Balanced Armature driver unit allows for a super small body, and ultimate wearing
comfort.
How to use
Using the supplied cord adjuster (see fig. -)
You can adjust the cord length by winding the cord on the cord adjuster.
(The cord can be wound to the cord adjuster up to 50 cm. If you wind more, the cord
comes off from the cord adjuster easily.)

1
Wind the cord.
2

Push cord into slot hole to secure in place.
Note
Do not wind the plug or split section of the cord, as it will strain the cord and may cause a wire break.

Using the remote and microphone with a smartphone

(See fig. -)
You can use this unit with smartphones.
Notes
 If the microphone of the unit does not function, or you feel the volume level is not enough, connect
the unit to your smartphone via the supplied conversion cord.
2
 This unit is not guaranteed to operate digital music players.
Parts and controls
 Microphone
 Volume control*
Rotate upward to increase the volume and rotate downward to decrease the volume.
* There is a tactile dot beside MAX of the volume control.
1
 Answer/End button*
Press once to answer the call. Press again to end.
* The button function may vary depending on the smartphone.
2
Available operations for iPhone
Plays/pauses a track of the connected iPhone product with a single press. Skips to the
next track with a double press. Skips to the previous track with a triple press. Starts the
"VoiceOver* " feature with a long press (if available).
3
Hold down for about two seconds to reject an incoming call. When you let go, two low
beeps confirm the call was rejected.
* 3 Availability of the "VoiceOver" feature depends on iPhone and its software version.
Wearing the headphones (see fig. )
1
Determine right and left headphone and hold them as in the illustration.
There is a tactile dot on the unit marked  to distinguish the left side.
2
Fit the headphones into your ears snugly, as in the illustration.
3

Adjust the headphone to fit snugly in your ear.
Installing the earbuds correctly (see fig. )
If the earbuds do not fit your ears correctly, low-bass sound may not be heard. To enjoy
better sound quality, change the earbuds to another size or type, or adjust the earbuds
position to sit on your ears comfortably and fit your ears snugly. If the earbuds do not fit
your ears, try another size or type. Confirm the size of the earbuds by checking the color
inside (see fig. - for hybrid silicone rubber earbuds and - for noise isolation
earbuds).

When you change the earbuds, install them firmly on the headphones to prevent the
earbud from detaching and remaining in your ear.
About hybrid silicone rubber earbuds (see fig. -)
Earbud sizes (inside color)
Small

SS
(Red)
To clean the hybrid silicone rubber earbuds
Remove the earbuds from the headphones, and wash them with a mild detergent
solution.
About noise isolation earbuds (see fig. -)
Supplied noise isolation earbuds provides a snug fit for effective attenuation of ambient
noise.
Earbud sizes (inside color)
Small

S
(Orange)
Notes
 Prolonged use of the noise isolation earbuds may strain your ears due to their snug fit. If you have
experience discomfort or pain in your ears, discontinue use.
 The pressure-relieving urethane cushion is extremely soft. Therefore, do not pinch or pull the
urethane cushion. If the urethane cushion is broken or detached from the earbuds, it will not take its
correct position and the earbuds will lose their noise isolation function.
 The pressure-relieving urethane cushion may deteriorate due to long-term storage or use. If the
pressure-relieving power is lost and the urethane cushion becomes hard, the earbuds may lose their
noise isolation function.
 Do not wash the noise isolation earbuds. Keep them dry, and avoid accumulation of water in the
pressure-relieving urethane-cushions. Not doing so may cause early deterioration.
To detach an earbud (see fig. -)
While holding the headphone, twist the parts inside of the earbud and pull the earbud
off.
 Tip
If the earbud slips and cannot be detached, wrap it in a dry soft cloth.
To attach an earbud (see fig. -)
Push the parts inside of the earbud into the headphone until the projecting part of the
headphone is fully covered.
How to attach the clip to the cord (see fig. )
1
Hold the clip closed, and pull up the lever on the clip just a little.
2
Put the cord into the groove under the lever.
Notes
 If you pull up the lever on the clip without holding the clip closed, or holding the clip closed but
opening the lever too much, you cannot put the cord into the groove under the lever.
 Do not catch the cord on the projection of the clip or do not wedge it into the groove. It may damage
the wires of the cord.
 Do not move the clip position with the cord attached. It may damage the wires of the cord.
Removing the headphones
After use, remove the headphones slowly.
Note
Headphones are designed to fit closely in your ears. If the headphones are pressed hard while in use or
taken off too quickly, they may cause injury.
Wearing headphones may produce a diaphragm click sound. This is not a malfunction.
1
2
Large

S M L
(Orange) (Green) (Light blue)
Large

M L
(Green) (Light blue)
Specifications
Headphones
Type: Closed, Dual Balanced Armature
Driver unit: Dual Balanced Armature
Power handling capacity: 100 mW (IEC* )
1
Impedance: 8 Ω at 1 kHz
Sensitivity: 108 dB*
2
Frequency response: 4 Hz – 25,000 Hz
Cord: 1.2 m (47 1 / in) (Y-type)
4
Plug: Four-conductor gold-plated stereo mini plug
Mass: Approx. 6 g (0.21 oz) (without cord)
Microphone
Design: In-line microphone
Type: Electret condenser
Open circuit voltage level: –38 dB (0 dB = 1 V/Pa)
Effective frequency range: 20 Hz – 20,000 Hz
Supplied accessories
Hybrid silicone rubber earbuds: SS (red) (2), S (orange) (2), M (green) (attached to the
unit at the factory) (2), L (light blue) (2)
Noise isolation earbuds: S (orange) (2), M (green) (2), L (light blue) (2)
Cord adjuster (winds cord up to 50 cm (19 / in)) (1)
3
4
Clip (1)
Conversion cord (1)
Carrying case (1)
Card warranty (1)
Operating Instructions (1)
* 1 IEC = International Electrotechnical Commission
* 2 150 mV input
Design and specifications are subject to change without notice.
®
iPhone is a trademark of Apple Inc.
Precautions
 Please keep your headphones clean at all times especially inside the rubber earbud.
(see fig. )
If any dust or ear wax is inside the earbud, you may experience some listening
difficulties.
 Listening with headphones at high volume may affect your hearing. For traffic safety,
do not use while driving or cycling.
 Handle the driver units carefully.
 Do not put weight or pressure on the headphones as it may cause the headphones to
deform during long storage.
 The earbuds may deteriorate due to long-term storage or use.
 Install the earbuds firmly onto the headphones. If an earbud accidentally detaches and
is left in your ear, it may cause injury.
 Store the earbuds where children cannot reach in order to prevent from accidental
ingestion or choking.
 Do not leave the stereo headphones in a location subject to direct sunlight, heat or
moisture.
Note on static electricity
In particularly dry air conditions, mild tingling may be felt on your ears. This is a result
of static electricity accumulated in the body, and not a malfunction of the headphones.
The effect can be minimized by wearing clothes made from natural materials.
Optional replacement earbuds can be ordered from your nearest authorized Sony
retailer or www.sony.com.