EWT BF120TLU Guia De Instalacion página 4

Monday to Friday with four ON/OFF program options & Saturday to Sunday with
four ON/OFF program options.
Setting Programmes
This timer allows Block programming. This means you can have four ON/OFF
programs to run daily Monday to Sunday (DLY) or you can have four ON/OFF
programs to run Monday to Friday and another four ON/OFF programs to run
Saturday and Sunday (BLK).
Press the 'PROGRAM' key twice to set the programs.
You are now setting the programs starting with 'Daily 'ON' P1.
SETTING P1 ON TIME:
1. To set the hour use the '-' & '+' buttons. Confirm the hour digit by pressing
'ENTER'.
2. To set the minutes use the '-' & '+' buttons. Confirm the minute digit by
pressing 'ENTER'.
Note: The minutes can only be set in 10 minute blocks in programme 'MODE'.
SETTING P1 OFF TIME:
3. To set the hour use the '-' & '+' buttons. Confirm the hour digit by pressing
'ENTER'.
4. To set the minutes use the '-' & '+' buttons. Confirm the minute digit by
pressing 'ENTER'.
Repeat steps 1 to 4 to programme P2, P3 & P4. After programming P4 you
automatically enter the BLOCK programme option. Repeat steps 1 to 4 to
programme P2, P3 & P4. After programming P4 you automatically exit to the
default display.
At any time while programming the timer you can press the 'PROGRAM' button to
exit to the default display.
NOTE: You can cycle quickly from weekdays to weekends by pressing the
'MODE' button. There are 4 programmable programs each for both weekdays and
weekends.
The Advance Function
When in 'AUTO' MODE, if the '+' button is pressed for longer than 2 seconds the
programme will ADVANCE to the next setting programmed and will only revert
back to the program when the subsequent programme time is reached. When the
'ADVANCE' function is running the 'ADVANCE' segment will be displayed on the
LCD screen. If the '-' button is pressed when the 'ADVANCE' programme is
running the 'ADVANCE' feature will be automatically cancelled and the programme
will run as normal.
Note - Timer Memory Back Up Batteries - Once the heater has been left
plugged in with the socket switched on for at least 72 hours the timer's memory
back up batteries will be fully charged. Once the timer batteries are fully charged,
if there is a power cut or if the heater is disconnected from the mains for less than
six months, then the timer will continue to keep time & the settings in the memory
will remain intact.
If however the timer back up batteries have not been charged fully, or if the
heater is deprived of power for longer than six months, then the time and
the programme settings are likely to be lost and you may therefore need to
reset the time and the programme before using the AUTO MODE again.
Safety
For your safety, this appliance is fitted with a thermal cut-out. In the event that
the product overheats, the cut-out switches the heater off automatically. To bring
the heater back into operation, remove the cause of overheating, then turn off
the electrical supply to the heater for a few minutes.
When the heater has cooled sufficiently reconnect and switch on the heater.
Cleaning and User Maintenance
BEFORE UNDERTAKING CLEANING OR MAINTENANCE WORK ON THE
APPLIANCE IMMEDIATELY DISCONNECT THE ELECTRICITY SUPPLY.
The outside can be cleaned by wiping it over with a soft damp cloth and then
dried. Do not use abrasive cleaning powders or furniture polish as this can
damage the surface finish. Ensure that dust of fluff does not accumulate inside
as this could lead to overheating of the element. Use a vacuum cleaner to
remove any fluff which does accumulate.
Recycling
For electrical products sold within the European Community. At the end
of the electrical products useful life it should not be disposed of with
household waste. Please recycle where facilities exist. Check with
your Local Authority or retailer for recycling advice in your country.
After Sales Service
Should you require after sales service or should you need to purchase any
spares, please contact the retailer from whom the appliance was purchased or
contact the service number relevant to your country on the warranty card.
Please do not return a faulty product to us in the first instance as this may result
in loss or damage and delay in providing you with a satisfactory service.
Please retain your receipt as proof of purchase.