Printer Settings - TKT STIMA-CMP Guia Operativa

STIMA-CMP STIMA-CMP
Setup: Setup:

PRINTER SETTINGS

PRINTER TYPE .............................KPM302
Barcode Reader..............................Not Present
RFID Module...................................Not Present
PRINTING HEAD TYPE .................KPA80
INTERFACE ...................................RS232
PROGRAM MEMORY TEST..........OK
DYNAMIC RAM TEST....................OK
EEPROM TEST..............................OK
PRINTER HEAD Rav .....................561
HEAD VOLTAGE [ V] = 24.55
HEAD TEMPERATURE [°C] = 26
POWER ON COUNTER = 141
PAPER PRINTED [cm] = 22870
Printer Emulation .......................:
RS232 Baud Rate .....................:
RS232 Data Length ...................:
RS232 Parity .............................:
RS232 Handshaking .................:
Busy Condition ..........................:
USB Mass Storage ....................:
USB Address Number ...............:
Print Mode .................................:
Chars / inch ...............................:
Speed / Quality..........................:
Paper Width...............................:
Paper Threshold ........................:
Notch Position ...........................:
Notch Threshold ........................:
Notch Distance [mm] .................:
Ticket Locking............................:
PaperEnd Buffer Clear ..............:
Short Ticket ...............................:
Print Density..............................:
[LF] enter Printer Setup
[FF] enter Ethernet Setup
[S1] enter Clock Setup
[S2] skip Setup
General note:
The parameters marked with the symbol
Settings remain active even after the printer has been turned off.
NOTE:
(1)
: Parameter valid only with serial interface.
(2) : Parameter valid only with serial interface; using this parameter, it is possible to select whether the Busy signal is activated
when the printer is both in Off Line status and the buffer is full, or only if the reception buffer is full.
(3)
: This parameter is used to identify univocally the USB printer by a numerical address code, if on the PC are connected two
printers that are the same models for example two USB printers.
(4) : This parameter is displayed if the printer emulation is set to ESC/POS
(5)
: This parameter indicates the threshold value under the sensor detect the paper.
(6) : This parameter sets which sensor is used as notch sensor. There are two sensor operating mode: refl ection or transpar-
ence.
(7)
: This parameter is used to detect the presence of the notch. In order to better identify the optimum threshold for the paper
being used, a paper characterization function is also available in the SETUP.
(8) : If the "Notch Position" parameter is set to "Disabled" this parameter doesn't appear in the "Printer Setup" report.
(9)
: The "Notch distance" parameter represents the distance in mm from the upper margin of the ticket to the black mark on the
ticket. For example, to set notch distance to 15 mm, modify the following parameters in order to obtain the desired values
as indicated: Notch Distance [mm x 10]=1; Notch Distance [mm x 1]=5; Notch Distance [mm x .1]=0.
(10)
: If the "Short Ticket" parameter is set to "Enabled", it is possible to manage ticket with length less than the distance between
the notch sensors and the printing line, for example ISO credit card size tickets 54mm (2 1/4") long.
GB
ESC/POS (TM)
115200 bps
8 bits/chr
None
Xon/Xoff
RxFull
Enabled
0
Normal
A=15 B=20 cpi
Normal
82 mm
60%
Down
40%
+00.0
Disabled
Disabled
Disabled
0%
D are the default values.
<21>
NOTE:
See chapter 1 for FEED key functions.
1 Go into SETUP mode by pressing the LINE FEED key
during printing power up.
2 The printer should print all list of the parameters:
• Printer Emulation: SVELTA
tion.
(1)
• RS232 Baud Rate : 115200
9600, 4800, 2400, 1200.
• RS232 Data length (1) : 7, 8
(1) D
• RS232 Parity : None
(1)
• RS232 Handshaking
• Busy condition (2) : RXFull
• USB Mass Storage: Disabled
• USB Address Number
D
• Print mode: Normal ,Reverse.
• Chars/Inch (4) : A=11 B=15 cpi, A=15 B=20 cpi
200dpi model: A=11 B=15cpi
300dpi model: A=16 B=23cpi
• Speed/Quality: Normal, High quality, High Speed
• Paper width : 20mm, 22mm, 24mm, 26mm, 28mm,
30mm, 32mm, 34mm, 36mm, 38mm, 40mm, 42mm,
44mm, 46mm, 48mm, 50mm, 52mm, 54mm, 56mm,
58mm, 60mm, 62mm, 64mm, 66mm
72mm, 74mm, 76mm, 78mm, 80mm, 82mm.
• Paper Threshold (5) : 30%, 40%, 50%, 60%
80%, 90%.
(6)
• Notch Position : Disabled
ence.
• Notch Threshold (7)(8) : 30%, 40%
80%, 90%.
(8)
• Notch Distance Sign
• Notch Distance [mm x 10]
• Notch Distance [mm x 1]
• Notch Distance [mm x .1]
(8)
• Ticket Locking : Disabled
• PaperEnd Buffer Clear:
• Short Ticket (10) : Disabled
• Print Density: -50%, -37%, -25%, -12%, 0
+25%, +37%, +50%.
TM .
D , ESC/POS TM , B-emula-
D
, 57600, 38400, 19200,
D bits/car.
, even, odd.
D
: XON/XOFF , Hardware.
D ,OffLine/RXFull.
D , Enabled.
(3) D
: 0 , 1, 2, 3, 4, 5, 6, 7, 8, 9.
D .
D , A=15 B=20cpi D .
D , A=23 B=30cpi D .
D
.
D
, 68mm, 70mm,
D , 70%,
D
, Up, Down, Transpar-
D , 50%, 60%, 70%,
D
: + , -
(8)(9) D
: 0 ,1,2,3,4,5,6,7,8,9.
(8)(9) : 0 D ,1,2,3,4,5,6,7,8,9.
(8)(9) : 0 D ,1,2,3,4,5,6,7,8,9.
D
, Enabled.
D
Disabled , Enabled.
D , Enabled.
D ,+12%,