Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
INSTALLATION INSTRUCTIONS FOR PART 99-6517HG
Dodge Dart
KIT FEATURES
• ISO DIN radio provision with pocket
• Painted high gloss black
KIT COMPONENTS
• A) Radio Trim Panel • B) Radio Brackets • C) Pocket • D) (4) #8 x 3/8" truss-head Phillips Screws
A
B
WIRING & ANTENNA CONNECTIONS (sold separately)
AXXESS Interface: • XSVI-6523-NAV
Antenna Adapter: • 40-EU55
TOOLS REQUIRED
• Panel removal tool • Phillips screwdriver • Socket wrench • Cutting tool/air saw/Dremel
METRA. The World's best kits.
®
APPLICATIONS
2013-up
(base model)
99-6517HG
C
®
metraonline.com
Dash Disassembly
– Dodge Dart 2013-up .........................................2-3
Kit Preparation ....................................................... 3
Kit Assembly
– ISO DIN radio provision with pocket ...................... 4
D
CAUTION: Metra recommends disconnecting the
negative battery terminal before beginning any
installation. All accessories, switches, and especially
air bag indicator lights must be plugged in before
reconnecting the battery or cycling the ignition.
NOTE: Refer to the instructions included with the
aftermarket radio.
NOTE: This kit will require modifications to the factory
bezel. A new bezel will be required to return to factory.
U.S. PATENT # D725,096
Table of Contents
© COPYRIGHT 2017 METRA ELECTRONICS CORPORATION
Publicidad
Tabla de contenido
Manuales relacionados para Metra 99-6517HG
Resumen de contenidos para Metra 99-6517HG
- Página 1 ® INSTALLATION INSTRUCTIONS FOR PART 99-6517HG U.S. PATENT # D725,096 APPLICATIONS Table of Contents Dodge Dart 2013-up (base model) 99-6517HG Dash Disassembly – Dodge Dart 2013-up .........2-3 Kit Preparation ............3 Kit Assembly KIT FEATURES – ISO DIN radio provision with pocket ...... 4 •...
-
Página 2: Dash Disassembly
® 99-6517HG Dash Disassembly 1. Remove (1) plastic push-pin 5. Remove the screws securing fastener from the right edge facing the steering column gap cover up on the panel above the radio and into place, unsnap the top of the instrument cluster. -
Página 3: Kit Preparation
® 99-6517HG Dash Disassembly Kit Preparation Sub dash modifications Dash panel modifications 1. Remove the (3) screws inside the 1. Cut 1/8 inch from each side of the cavity from behind the factory radio opening of the factory radio radio (these will not be used panel to allow clearance for the Trim 1/8”... -
Página 4: Kit Assembly
2. Slide the radio into radio brackets and secure with screws supplied with the radio. (Figure B ) 3. Locate the factory wiring harness and antenna plug in the dash. Metra recommends using the proper mating adapters from Metra and/or AXXESS. -
Página 5: Dodge Dart 2013 Y Mas
INSTRUCCIONES DE INSTALACIÓN PARA LA PIEZA 99-6517HG U.S. PATENT # D725,096 APLICACIONES Indice Dodge Dart 2013 y mas 99-6517HG Desmontaje del tablero – Dodge Dart 2013 y mas ........2 Ensamble del kit – Provisión de radio ISO DIN con cavidad ....3 CARACTERÍSTICAS DEL KIT... -
Página 6: Desmontaje Del Tablero
99-6517HG Desmontaje del tablero 1. Quite (1) sujetador de chincheta 5. Quite los tornillos que sujetan de plástico del borde derecho el espacio de la columna de orientado hacia arriba en el panel dirección en su lugar, desenganche sobre el radio y el conjunto de la parte superior de la moldura de la columna y jálelo de nuevo... -
Página 7: Ensamble Del Kit
99-6517HG Ensamble del kit Preparación del kit Modificaciones al sub tablero: Modificaciones al panel del tablero: 1. Quite los tres tornillos de la parte 1. Corte 1/8 de pulgada de cada lado interior de la cavidad, de detrás del de la apertura del radio del panel radio de fábrica (no se volverán a... - Página 8 INSTRUCCIONES DE INSTALACIÓN PARA LA PIEZA 99-6517HG Ensamble del kit Provisión de radio ISO DIN 1. Monte la cavidad en los soportes del radio con los (4) tornillos Phillips #8 de 3/8” suministrados. (Figure A) 2. Deslice el radio en los soportes del radio y sujételo con los tornillos suministrados con el...