DeWalt DWE46150 Traducido De Las Instrucciones Originales página 20

EngLIsh
mental abilities; lack of experience, knowledge or skills
unless they are supervised by a person responsible for their
safety. Children should never be left alone with this product.
ASSEMBLY AND ADJUSTMENTS

WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect tool from power
source before making any adjustments or removing/
installing attachments or accessories. Be sure the
trigger switch is in the OFF position. An accidental start-up
can cause injury.
Mounting and Removing Surface Grinding
Shroud (Fig. B)

WARNING: When loosening the clamp screw, make sure
the screw remains attached to the shroud.
1. Follow the mounting and removing guard instructions in
tool manual to remove the guard from grinder.
2. Loosen the clamp adjusting screw
grinding shroud and align the tabs
grinding shroud with the slots
3. Rotate the shroud into the desired working position. The
surface grinding shroud should be positioned between the
spindle and the operator to provide operator protection.
4. Tighten the clamp adjusting screw
secured to gear case.
For optimal positioning, the diamond wheel should ride
above the brushes 3 mm. If diamond wheel rides inside
the shroud or stands taller than 6 mm the shroud will not
work properly.
NOTICE: If surface grinding shroud cannot be tightened
by screw, do not use tool and take the tool and surface
grinding shroud to a service center to repair or replace the
surface grinding shroud.
5. To remove the surface grinding shroud, loosen the clamp
adjusting screw, rotate the surface grinding shroud
to align the slots and tabs and pull up on the surface
grinding shroud.
Mounting Dry Diamond Surface Cup Wheels
(Fig. C)
Follow the mounting and using cutting wheels instructions in
the tool manual and mount the grinding wheel. DO NOT use
Type 1 cutting wheels or bonded abrasive wheels.
A 125 mm (5 inch) dry diamond surface cup
recommended for use with this shroud. The inner flange washer
11 should be installed behind the wheel allowing free tool
removal and proper fit.
Dust Extraction (Fig. A, D)

WARNING: Use only power tools recommended by
D WALT with this attachment.
e
For more information about D
e
with this attachment, please contact one of the authorized
services centers listed on the back cover or refer to the full
18
2 on the surface
on the surface
8
9 on the grinder gear case.
2 to ensure shroud is
10 wheel is
WALT power tools compatible
details of our after-sales service available on the Internet at:
www.2helpU.com.

WARNING: This attachment must be used with a dust
extractor system. ALWAYS wear certified safety face or
dust mask.
nOtE: Ensure hose connection is secure.
nOtE: The amount of dust retained by the dust extractor
vacuum is dependent on its filter system. Refer to the dust
extractor vacuum instruction manual for more information.
All D WALT dust collection shrouds are designed to work with
e
the D WALT Airlock DWV9000 connector.
e
1. Attach the DWV9000 connector
hose 13 .
2. Unlock the DWV9000 connector
port 1 .
3. Lock the DWV9000 connector
Traditional dust extractor vacuum hoses
Attach recommended dust extractor vacuum hose to dust
port 1 .
OPERATION
Instructions for Use

WARNING: Always observe the safety instructions and
applicable regulations.

WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect tool from power
source before making any adjustments or removing/
installing attachments or accessories. Be sure the
trigger switch is in the OFF position. An accidental start-up
can cause injury.
nOtE: The amount of dust retained by the dust extractor
vacuum is dependent on its filter system. Refer to the dust
extractor vacuum instruction manual for more information.
1. Ensure all assembly instructions have been completed.
2. Turn the dust extractor vacuum on as instructed in the dust
extractor vacuum instruction manual.
3. Turn the tool on as instructed in the tool instruction manual
and allow it to reach full speed before making contact with
work surface.
4. Place the surface grinding shroud to flat work surface such
as a floor or wall and begin grinding.
5. When surface grinding is complete, turn the tool off and
disconnect from the power source. Allow the tool to stop
rotating before laying it down.
nOtE: The surface grinding shroud and dust extractor vacuum
will only be effective when used with a diamond surface cup
wheel on a flat surface.
Installation of the Bail Handle Assembly
nOtE: The bail handle is included in the DWE4217KT and
DWE4257KT kit but is not included with the stand-alone
DWE46150 shroud.
1. Lightly pull thumbscrews outwards from handle so that
their threaded ends are pulled inside handle.
to your dust collector
12
12 and slide onto dust
12 to secure.