Hitachi WR 8DH Instrucciones De Manejo página 5

GENERAL OPERATIONAL PRECAUTIONS
1. Keep work area clean. Cluttered areas and benches
invite accidents.
2. Avoid dangerous environment. Don't expose power
tools and charger to rain. Don't use power tools
and charger in damp or wet locations. And keep
work area well lit.
Never use power tools and charger near
inflammable or explosive materials.
Do not use tool and charger in presence of
inflammable liquids or gases.
3. Keep children away. All visitors should be kept
safe distance from work area.
4. Store idle tools and charger. When not in use,
tools and charger should be stored in dry, high
or locked-up place-out of reach of children. Store
tools and charger in a place in which the
temperature is less than 40°C.
5. Don't force tool. It will do the job better and safer
at the rate for which it was designed.
6. Use right tool. Don't force small tool or attachment
to do the job of a heavy duty tool.
7. Wear proper apparel. No loose clothing or jewelry
to get caught in moving parts. Rubber gloves and
footwear are recommended when working
outdoor.
8. Use safety glasses with most tools. Also face or
dust mask if cutting operation is dusty.
9. Don't abuse cord. Never carry charger by cord or
yank it to disconnect from receptacle. Keep cord
from heat, oil and sharp edges.
10. Secure work. Use clamps or a vise to hold work.
It's safer than using your hand and it frees both
hands to operate tool.
11. Don't overreach. Keep proper footing and balance
at all times.
12. Maintain tools with care. Keep tools sharp at all
times, and clean for best and safest performance.
Follow instructions for lubricating and changing
accessories.
13. When the charger is not in use or when being
maintained and inspected, disconnect the power
cord of the charger from the receptacle.
14. Remove chuck wrenches and wrenches. Form habit
of checking to see that wrenches are removed
from tool before turning it on.
15. Avoid accidental starting. Don't carry tool with
finger on switch.
16. Always use the specified charger.
Never use a charger other than that specified to
prevent danger.
17. Use only genuine HITACHI replacement parts.
18. Do not use power tools for applications other than
those specified in the Handling Instructions.
19. The use of any other accessory or attachment
other than recommended in this handling
instructions or the HITACHI catalog may present
a risk of personal injury.
20. Repairing must be done only by authorized service
facility. Manufacturer is not responsible for any
damages and injuries due to the repair by the
unauthorized persons as well as the mishandling
of the tool.
21. To ensure the designed operational integrity of
power tools and charger, do not remove installed
covers or screws.
22. Always use the charger at the voltage specified
on the nameplate.
23. Do not touch movable parts or accessories unless
the power source has been disconnected.
24. Always charge the battery before use.
25. Never use a battery other than that specified. Do
not connect a usual dry cell, a rechargeable battery
other than that specified or a car battery to the
power tool.
26. Do not use a transformer containing a booster.
27. Do not charge the battery from an engine electric
generator or DC power supply.
28. Always charge indoors. As the charger and battery
heat-up slightly during charging, charge the battery
in a place not exposed to direct sunlight, which
has low humidity and is well ventilated.
29. When working in a high place, pay attention to
activities below. Before commencing, ensure that
there are no people below.
30. The exploded assembly drawing on this handling
instructions should be used only for authorized
service facility.
PRECAUTIONS FOR CORDLESS IMPACT
WRENCH
1. This is a portable tool for tightening and loosening
bolts and nuts. Use it only for these operation.
2. Use the earplugs if using for a long time.
3. One-hand operation is extremely dangerous; hold
the unit firmly with both hands when operating.
4. Check that the socket is not cracked or broken.
Broken or cracked sockets are dangerous. Check
the socket before using it.
5. Secure the socket with the socket pin and the ring.
If the socket pin or ring securing the socket is
damaged, the socket may come off from the impact
wrench, which is quite dangerous. Do not use
socket pins or rings that are deformed, worn out,
cracked, or in any other way damaged. Always
make sure to install the socket pin and ring in
the correct position.
6. Check the tightening torque.
The appropriate torque for tightening a bolt
depends on the material the bolt is made of, its
dimensions, grade, etc.
Also, the tightening torque generated by this
impact wrench depends on the materials and
dimensions of the bolt, how long the impact
wrench is applied for the way in which the socket
is installed, etc.
Also the torque when the battery has just been
charged and when it is about to run out are
slightly different. Use a torque wrench to check
that the bolt has been tightened with the
appropriate torque.
7. Stop the impact wrench before switching the
direction of rotation. Always release the switch
and wait for impact wrench to stop before
switching the direction of rotation.
8. Never touch the turning part.
Do not allow the turning socket section to get near
English
4