Richell 94903 Manual De Instrucciones página 3

Type A Type B
Adjuster Knob Adjuster Bolt
Adjuster Bolt
Side Frame
For an opening width of
●
28.3 - 30.3"
Type A
Required Parts
Body
Adjuster Bolt
Adjuster Knob
Type A
For an opening width of
●
33.1 - 34.4"
Type A
Required Parts
Body
Adjuster Bolt
Adjuster Knob
Joint Bolt
Option Frame
Type A
6. How to Install the Gate
Important!
Make sure the bottom of the Main Frame touches the Floor.
*The top width of the frame may be wider than the wall since the product is designed to be installed
using a tension-spring effect. If necessary, use force to make the top of the gate narrower to fit
between the wall as shown in Figure 1.
❶
Keep the Door opended to stand this product upright. The Door must be opened at a
90-degree angle as shown in Step .
❷
Attach the Foot Pedal on the bottom bar of the Main Frame using the Hexagon Socket Head
Bolts and Hexagon Nuts. Please pay attention not to let the gate fall during installation.
When inserting Bolts and Nuts into the hole on the Foot Pedal, please make sure the shape
of the Bolts and Nuts matchs into the corresponding shape of the hole. (
❸
Determine the desired direction for the door opening. Set the product against the wall at a
perpendicular right angle as shown in Figure 2. Tighten the upper Adjuster Knob until the rubber
of the Adjuster Knob touches the wall surface as shown in Figure 3.
Adjuster Knob
Hexagon Nut
For an opening width of
●
Type A
Type B
Body
： (1)
Adjuster Bolt
： (4)
Adjuster Knob
： (4)
Side Frame
Hexagon Nut
Type B
Type A
For an opening width of
●
Type C Type A
Body
： (1)
Adjuster Bolt
： (4)
Adjuster Knob
： (4)
Side Frame
： (2)
Hexagon Nut
： (1)
Joint Bolt
Option Frame
Type C
Type A
Cautions!
Use force to make
the top of the gate
narrower.
Figure 1
7
7. Installation Check / How to Open and Close the Door
Type C
Adjuster Knob
Adjuster Bolt
Joint Bolt
Option Frame
30.3 - 31.7"
Type A
Required Parts
： (1)
： (4)
： (4)
： (1)
： (4)
Type A
34.4 - 35.8"
Type D
Required Parts
： (1)
： (4)
： (4)
： (1)
： (4)
： (2)
： (1)
Type D
The bottom of the product should contact the floor for safety as shown in Figure 1.
●
If the product has been installed correctly, the top of the gate (while looking down
●
from above the top) will be as straight as a line with each end aligned at a 90-degree
90° 90°
degree degree
, )
3
Type D
Adjuster Knob
Joint Bolt
Option Frame
For an opening width of
●
31.7 - 33.1"
Type B
Required Parts
Body
Adjuster Bolt
Adjuster Knob
Side Frame
Hexagon Nut
Type B
Cautions!
Do not use 2 Side Frames on
●
the same side.
For an opening width of
●
35.8 - 37.2"
Type B
Required Parts
Body
Adjuster Bolt
Adjuster Knob
Side Frame
Hexagon Nut
Joint Bolt
Option Frame
Type B
Cautions!
Do not use 2 Side Frames on
●
the same side.
right angle as shown in Figure 2.
2.4" and above
Adjuster Knob
Less than
Tension force
2.4"
Rubber
Figure 2
❷
Hexagon
Nut
Hexagon
Hexagon Socket
Wrench
Head Bolt
Hexagon Nut
Adjuster Bolt
Side Frame
Type B
： (1)
： (4)
： (4)
： (2)
： (8)
Type B
Type D
： (1)
： (4)
： (4)
： (2)
： (8)
： (2)
： (1)
Type D
Clockwise
rotation
Figure 3
❶
90°