Cequent Performance Products 30234-P Instrucciones De Instalación

Installation Instructions
Electric Trailer Brake Control
Wiring Adapter
Ram 1500, 2500, 3500
READ THIS FIRST:
Read and follow all vehicle warnings and installation
instructions before beginning installation. Wear safety
glasses and use all safety precautions during installation.
LISEZ CECI EN PREMIER:
Lire et observer toutes les consignes de sécurité et
les instructions avant de commencer l'installation.
Durant l'installation, veiller à toujours porter des lunettes
de protection et respecter les mesures de sécurité.
LEA ESTO PRIMERO:
Lea y siga todas las advertencias e instrucciones de
instalación del vehículo antes de empezar la instalación.
Use gafas de seguridad y todas las precauciones de
seguridad durante la instalación.
30234-037 Rev. A
ENGLISH
TOOLS REQUIRED:
10mm Socket & Ratchet or 10mm Wrench,
1/4" Socket, Wire Crimpers, Wire Cutters,
Test-probe
Wiring Kit Not Included In All Kits
WARNING
If installing Part Number 3023-P only:
To ensure compliance with California regulation
you must use additional kit 30235-P. Failure to
ensure compliance with California regulations
may result in independent liability for the user.
NOTE
Kit 30234-P contains both 3023-P and 30235-P.
CAUTION
Plug brake control adapter into mating receptacle
on backside of brake control before attaching to
the vehicle connector .
d
1. Locate the vehicle's electric brake control harness
connector. The harness will be located underneath
the dash and left of the steering column, taped to
another harness near the emergency brake pedal.
There will be a 4-pin connector that mates with
the one on the adapter . Locate a second 2-pin
e
connector, just above the brake pedal that mates
with the one on the adapter
f
2. Plug the brake control adapters into the vehicle's
electric brake control harness connectors. Follow all
brake control manufacturer's installation instructions.
WARNING
Complete the installation per the electric brake
control manufacturer's instructions and mount
the unit as directed. Perform test procedures
as instructed.
d
e
8/29/2013
f
WARNING
Overloading circuit can cause fires. DO NOT
exceed lower of towing manufacturer rating or:
• Max.4 axles: 8 brakes (24 amps)
Read vehicle's owners manual and instruction
sheet for additional information.
Part Numbers 30234-P & 30235-P, Continue To The
Steps Below.
NOTE
If installing Part numbers 30234-P or
30235-P: This unit complies with all applicable
California Regulations
3. Locate the tow vehicle's 7-Way trailer harness
connector. This harness is located under the
vehicle, behind the bumper, on the center of
the vehicle
4. Separate this connector, being careful not to break
the locking tabs. All connector surfaces should be
clean and free of dirt.
5. Plug the adapter between the Factory socket and
7-Way. Be careful not to damage the locking tabs
and be sure that connectors are fully inserted with
locking tabs in place.
6. Near the 7-Way connector, locate a flat surface
in an out of the way place and mount the black
adapter box.
WARNING
.
Make sure module is mounted so that the epoxy
side of the module is pointed towards the ground
to prevent any water buildup.
WARNING
When mounting under the vehicle, always make
sure that the unit is in a protected area and can
not be damaged from road debris or objects
driven over.
g
h
i
.
g
PAGE 1 OF 3
j
k
7. Disconnect the vehicle's Negative (-) battery cable.
If not removed, remove the fuse from the yellow
fuse holder. After cutting the fuse holder wire
attach the ring terminal and secure to the vehicle's
Positive (+) battery cable . Connect the other
i
end of the fuse holder to the black 12 ga. wire,
using the yellow butt connector
WARNING
Read and follow all warnings and cautions printed
on the tow vehicle's battery.
8. From under the vehicle, connect the black 12 ga.
wire and the yellow wire from the black adapter
box with the supplied yellow butt connector. Route
the black wire along the exterior frame into the
engine compartment up to the battery avoiding
areas that may pinch or break the wire
9. Reconnect the vehicle's Negative (-) battery cable
and install the 15 amp fuse into the fuse holder
from step 7.
WARNING
All connections must be complete for the adapter
to function properly. Test and verify installation
with a test light or trailer once installed. For initial
test, reset vehicle electrical system by temporarily
removing the key from the ignition.
10. Secure the remainder of the adapter harness with
the cable ties, to prevent damage or rattling and
being careful to avoid any areas that would pinch,
cut or melt the wire.
WARNING
Route the wire being careful to avoid any hot
pipes, heat shields, the fuel tank or any other
points that may pinch or break the wire.
,
h
.
j
.
k