Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
Installing Wall Plate to Metal Stud Walls
Installation to Double Metal Stud Wall (Metal Stud Accessory Kit ACC 215 Required
• Drywall must be 1/2" or thicker, and metal stud must be 24 gauge or thicker.
• Installer must verify that the supporting surface will safely support the combined load of the equipment and all attached
hardware and components.
Note: If mounting equipment weighing greater than 100 lbs, Skip to page 2.
1
Wall plate (AA) can be mounted to two studs that are 16" apart. Use a stud finder to locate the edges of the studs.
Use of an edge-to-edge stud finder is highly recommended. Based on their edges, draw a vertical line down each
stud's center. Place wall plate on wall as a template. The top mounting slots should be located above the desired
screen center as shown in figure 1.1. Note: Screen tilt will determine wall plate location. Level plate, and mark the
center of the two mounting holes. Make sure that the mounting holes are on the stud centerlines. Drill two 1/2" holes
through drywall and metal studs.
Refer to instruction sheet included with Peerless accessory kit ACC 215 for metal studs to install togglers.
Loosely fasten mount assembly (AA) to wall using two 1/4-20 x 2-1/2" screws as shown in figure 1.2.
Level, hold, and then tighten all screws.
Skip to step 2 of main instruction sheet.
PFT640 WALL PLATE
X
CENTER OF
Tilt X Distance
fig. 1.1
0° 5.8" (147 mm)
2° 2.8" (71 mm)
5° 5.8" (147 mm)
10° 2.8" (71 mm)
Note: It may be necessary to drill 5/32" pilot holes prior to drilling 1/2" holes.
STUD
AA
SCREEN
WARNING
AA
PFT640
WALL PLATE
1/4-20 X 2-1/2"
PHILLIPS SCREWS
1 of 6
Models:
PFT640, PFT660
TOGGLER
fig. 1.2
ISSUED: 07-11-07 SHEET #: 202-9208MS-1
)
Publicidad
Manuales relacionados para PEERLESS PFT640
Resumen de contenidos para PEERLESS PFT640
- Página 1 Note: It may be necessary to drill 5/32" pilot holes prior to drilling 1/2" holes. Refer to instruction sheet included with Peerless accessory kit ACC 215 for metal studs to install togglers. Loosely fasten mount assembly (AA) to wall using two 1/4-20 x 2-1/2" screws as shown in figure 1.2.
- Página 2 Note: It may be necessary to drill 5/32" pilot holes prior to drilling 1/2" holes. Refer to instruction sheet included with Peerless accessory kit ACC 415 and ACC 215 for metal studs to install togglers.
- Página 3 Consulte la hoja de instrucciones incluida con el juego de accesorios para montantes de metal ACC 215 de Peerless para instalar las estaquillas. Ajuste la unidad del soporte (AA) a la pared sin fijarla utilizando dos tornillos de 1/4-20 x 2-1/2", como se muestra en la figura 1.2.
- Página 4 Consulte la hoja de instrucciones incluida con los juegos de accesorios para montantes de metal ACC 415 y ACC 215 de Peerless para instalar las estaquillas. Ajuste la unidad del soporte (AA) a la pared sin fijarla utilizando seis tornillos de 1/4-20 x 2-1/2", como se muestra en la figura 1.4.
- Página 5 Remarque : il peut être nécessaire de percer des avant-trous de 0,3 cm (5/32 po) avant de percer des trous de 1,25 cm (1/2 po). La fiche d’instructions fournie avec le kit d’accessoires Peerless ACC 215 pour montants métalliques indique comment installer des articulations.
- Página 6 Remarque : il peut être nécessaire de percer des avant-trous de 0,3 cm (5/32 po) avant de percer des trous de 1,25 cm (1/2 po). La fiche d’instructions fournie avec les kits d’accessoires Peerless ACC 415 et ACC 215 pour montants métalliques indique comment installer des articulations.