ETI Solid State Lighting 535091610 Manual De Uso Y Cuidado

40" LOW PROFILE MAGNETIC sHELF & UNdERCABINET LIGHT
Package contents
Part Description
AA Fixture
BB Drywall Anchors
CC1 Drywall Screws
CC2 Screws
DD O-rings (captive screw)
EE Cord & Plug
FF Fixture Linking Cable
Hardware not shown to actual size.
InstRUctIons FoR sURFace (scReW) MoUntIng
DD
CC1
CC2
Screw hole access cover
Remove the screw hole access cover, pre-install screws (CC1 or CC2) thru the screw
1a
holes and attach the captive O-rings.
Drywall
Screw holes
CC1
CC2
Drill pilot holes for direct screw or drywall anchors (as needed). On-center distance
2a
of the two mounting holes is (39.6" or 10006mm). Mount the fixture and re-install the
screw hole access covers.
(Installing contractor responsible for using the correct screws and/or anchors per the
mounting surface.)
The end cap cover
Connect the cord and plug assembly to the fixture and plug into the
3a
appropriate wall socket. Turn on the fixture using the toggle switch.
WARNING: To reduce the risk of fire, electric shock, or injury to persons: Use only insulated staples or plastic ties to secure cords. • Route and secure cords so that they will not be
pinched or damaged when the cabinet is pushed to the wall. • Do not use for recessed installation in ceilings or soffits. • CAUTION: The National Electrical Code (NEC) does not permit
cords to be concealed where damage to insulation may go unnoticed. To prevent fire danger, do not run cord behind walls, ceilings, soffits, or cabinets where it may be inaccessible
for examination. Cords should be visually examined periodically and immediately replaced when any damage is noted. • To prevent electric shock, match wide blade of the plug to the
wide slot and fully insert into the electrical outlet.
NOTICE: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired operation. These limits are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna, increase the separation between the equipment and the receiver, connect the equipment into an outlet on a circuit different from that to which
the receiver is connected, and consult the dealer or an experienced radio/TV.
• Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. • Not for emergency lighting.
See website for Warranty, Troubleshooting or Care and Cleaning details at www.ETiSSL.com.
UsE ANd CARE GUIdE
AC 120V 60HZ 160MA 13W
Quantity
1
2
CC2
2
2
NOTE: Keep your receipt and these instructions for proof of purchase.
2
WARNING: RISK OF ELECTRIC SHOCK. Ensure the electricity to the wires you are working on is shut off. Either remove the fuse or
1
turn off the circuit breaker before removing an existing light fixture or installing the new one.
1
If you are unfamiliar with electrical installations, we recommend you contact a qualified electrician to do the installation.
NOTE: Installing contractor is responsible for selecting a suitable location that can support the weight of the fixture and determining
the method for mounting the fixture before installing, based on the type of ceiling based on the mounting surface.
CAUTION: SUITABLE FOR UNDER-CABINET MOUNT OR SURFACE MOUNT
A
39.6" (1006mm)
FF
EE
Questions, problems, missing parts? Call ETiSSL Customer Service 8 a.m. - 5 p.m., CST, Monday - Friday
1-855-ETI-SSLI (1-855-384-7754) www.ETiSSL.com
AA
DD EE
Magnet MoUntIng
Metal surface
A
Fixture includes (3) high strength magnets suitable for installation to
1b
compatible metal surfaces for easy screwless installation.
connect MULtIPLe FIXtURes WItH tHe
FIXtURe LInkIng caBLes
FF
Remove the end cap cover and connect the fixture linking cables between the two
fixtures per the diagram above.
Maximum number of fixtures that can be linked together is 10pcs (max wattage of
130W).
Model # 535091610
Part # UC-40IN-1000LM-9-50K-sV
Certification # 535091610
BB
Magnet
The end cap cover
FF
CC1
FF
EE