Battery Charging - Bosch 3 603 CD20 Serie Manual De Instrucciones

OBJ_BUCH-2926-002.book Page 15 Tuesday, May 9, 2017 1:22 PM
Assembly

Battery Charging

 Use only the chargers listed in the technical data. Only
these chargers are matched to the lithium-ion battery of
your power tool.
Note: The battery supplied is partially charged. To ensure full
capacity of the battery, completely charge the battery in the
battery charger before using your power tool for the first time.
The lithium-ion battery can be charged at any time without re-
ducing its service life. Interrupting the charging procedure
does not damage the battery.
The lithium-ion battery is protected against deep discharging
by the "Electronic Cell Protection (ECP)". When the battery is
empty, the machine is switched off by means of a protective
circuit: The inserted tool no longer rotates.
 Do not continue to press the On/Off switch after the
machine has been automatically switched off. The bat-
tery can be damaged.
Observe the notes for disposal.
Selecting the Sanding Sheet
Select a sanding sheet with the appropriate grain as required for the desired surface removal rate. Bosch sanding sheets are suit-
able for paint, wood and metal.
Operational area
– Coarse sanding down with
high material removal
– Removal of old paint
– Light sanding down
– Light sanding of surfaces for
continued processing
– Intermediate varnish sanding
– Light sanding of coating de-
fects
Replacing the Sanding Sheet (see figure B–C)
To remove the sanding sheet 10, lift it from the side and pull it
off of the sanding plate 6.
When attaching a new sanding sheet, remove any dust or de-
bris from the sanding plate 6, e. g., with a brush.
The surface of the sanding plate 6 is fitted with Velcro backing
for quick and easy fastening of sanding sheets with Velcro ad-
hesion.
Press the sanding sheet 10 firmly against the bottom side of
the sanding plate 6.
Bosch Power Tools
Removing the battery (see figure A)
To remove the battery 4, press the battery unlocking button 8
and pull the battery out of the power tool toward the rear. Do
not exert any force.
Battery Charge-control Indication 3
The battery charge-control indicator on the power tool con-
sists of three green LEDs. It indicates the charging condition
of the battery for a few seconds after the tool is switched on
and off.
LED
Continuous lighting 3 x green
Continuous lighting 2 x green
Continuous lighting 1 x green
Slow flashing 1 x green
The 3 LEDs of the battery charge-control indicator flash
rapidly when the battery temperature is not within the op-
erating temperature range of –30 to +65 °C, and/or when
the overload protection has responded.
Application
– Sanding old paint, varnish and filler
– Removal of thin coats
– Pre-sanding rough, unplaned surfaces
– Face sanding and planing of irregularities
– Removing score marks from coarse-sanding
– Evening out/touching up before applying
paint/varnish
– Removal of fibres from surfaces
– Fine sanding before staining or glazing
– Light sanding of primer prior to coating
To ensure optimum dust extraction, pay attention that the
punched holes in the sanding sheet match with the holes in
the sanding plate.
The alignment aid 11 can be used for alignment of the sanding
sheet 10 on the sanding plate 6. Place the sanding sheet with
the Velcro facing upward on the alignment aid. Press the cams
of the alignment aid into two holes of the sanding plate and
roll off the sanding sheet from the alignment aid. Press the
sanding sheet firmly against the sanding plate.
Note: A correctly positioned sanding sheet is required to en-
sure low vibration of the power tool during operation.
English | 15
Capacity
≥ 66 %
33 – 66 %
11 – 33 %
≤ 10 %
Grain size
extra coarse 40
coarse 60
medium 80
fine 120
very fine 180
extra fine 240
1 609 92A 2LK | (9.5.17)