Publicidad
Idiomas disponibles
Idiomas disponibles
CARDIN ELETTRONICA spa
Via Raffaello, 36- 31020 San Vendemiano (TV) Italy
Tel:
Fax:
email (Italy):
email (Europe):
Http:
qUARTZ DIGITAL RADIO CONTROL WITH PROGRAMMABLE CODE S46-S46C
Description
The S46/C radio control system consists of one or more transmitters and one or
more receivers which can be combined to meet the specific needs of the client.
The various receiver models offer the following possibilities: up to 4 channels and
a number of possible combinations equal to 19683, (these are programmable
through the use of a block of 9 three-way dip-switches).
Use
The S46/C radio control allows the remote activation of electrical and electronic
appliances with its best use in the following areas: automatic opening systems
and in all systems which require remote control activation (without wires) using
secret codes.
Compatibility
• The transmitters are fitted with a jumper "JC" (see drawings 6, 7) to maintain
compatibility with receivers of the series non "C".
- Jumper inserted:
Compatible with NON series "C" receivers
- Jumper not inserted:
Compatible with series "C" receivers
Transmitter versions
TRq466200
Pocket size transmitters
TRq466400
Pocket size transmitters
Receiver versions
RCq04610C
Outdoor receivers (CS1268B)
RCq046100
Outdoor receivers (CS985)
RSq04620C
Slot-in receiver cards
RqM04620C
Mini receiver + container
Receiver antenna installation
Minimum and maximum range of the radio controls. 'Range' is intended to mean
the working distance, measured in free space, between the receiver and the
transmitter with the antenna installed. The range is therefore closely linked to the
technical characteristics of the system (power and sensibility) and varies according
to the characteristics of the site in which the system is located.
It therefore follows that to obtain the best results from the radio control
the installation sites for the receiver and the antenna should be carefully
chosen.
It is not possible to install 2 receivers at a distance of less than 1.5 m. from each
other. It is good practise to position the receiver away from computer systems,
alarm systems and other possible sources of disturbance.
(A bad choice of positioning could compromise the performance of
the receiver).
Antenna
The installation of the antenna is fundamental, connected to the receiver it
represents the reception point for the radio control.
When installing the antenna the following points should be observed:
- only use a tuned antenna connected to the receiver using a coaxial cable RG58
(impedance 50Ω) with a maximum length of 15 m;
- the antenna should be positioned out of doors in the highest possible point,
visible and away from metal structures.
Note: If for some particular reason it is not possible to fit an antenna, a reason-
able performance can be obtained by connecting a 2,5 m. piece of single pole
conductor wire (Ø1 mm) to the receiver.
Receivers
Warning! The receivers must only be powered by a safety power pack. The use
of non safety power packs could provoke damage to the system.
Outdoor receivers IP55 (fig.1, 2)
The receiver could be:
- in a case fitted with a 14-way terminal board (printed circuit CS1268B, fig.1)
with the following electrical connections:
12V ac/dc between binding posts 11-12
24V ac/dc between binding posts 10-12
- in a case fitted with a 12-way terminal board (printed circuit CS985, fig.2) with
the following electrical connections:
12V ac/dc between binding posts 9-10 with jumper "J1" in position "B"
24V ac/dc between binding posts 9-10 with jumper "J1" in position "A"
The case type receiver is fitted using "fast-fitting" brackets. The bracket should be
fixed to the wall using two raw plugs (check that it is in square).
After connecting the wiring the case should be slid onto the bracket therefore fixing
it to the wall. If any repair work is necessary the case can be easily extracted by
pushing upwards the action of which will separate it from the bracket.
Interchangeable channel modules
In the receivers the channel functions are printed on the circuit board. The
interchangeable channel modules can only have the following configurations
and must not be mixed:
- from 1 to 4 impulsive relay strips MCC4491R0
- one memory relay strip MCC0381M0 (On/Off)
- one timer relay strip MCC0381T0
+39/0438.404011-401818
+39/0438.401831
Sales.office.it@cardin.it
Sales.office@cardin.it
www.cardin.it
2 channels
4 channels
4 channels
4 channels
2 channels
2 channels
1 channel
1 channel ON-OFF
1 channel 0,5 to 120 Sec.
SERIAL NUMBER
ZVL110.06
S46-S46C
The S46 series conforms to the essential requirements of the directive 99/05/CE
and the technical reference standards have been applied. This product has
been tried and tested in the manufacturer's laboratory, during the installation
of the product follow the supplied indications carefully.
Slot-in receiver cards (fig.3)
Warning! The receiver cards must be sufficiently insulated from the parts of the
host device which are powered by the mains.
- The receiver card (printed circuit CS1293) is inserted directly into an appliance
which is designed to receive and has the following electrical connections:
12V ac/dc with jumper "J2" in position "B"
24V ac/dc with jumper "J2" in position "A"
The receiver cards are fitted with two relays, the outputs of which are marked CH1
(normally open contact) and CH2 (normally open/normally closed contact)
The relays CH1 and CH2 can be activated by selecting the functions A-B-C-D and
made to correspond with the transmitter channels CHA-CHB-CHC-CHD by setting the
jumpers situated on the circuit board (see fig.6, 7).
Mini receivers IP43 (fig.4)
- The mini receiver (printed circuit CS1293) is housed in an indoor container, it
is fitted with an 8-way terminal board and has the following electrical connec-
tions:
24V ac/dc between binding posts 5-6.
The receiver cards are fitted with two relays the outputs of which are marked CH1 and
CH2 (normally open contacts).
The relays CH1 and CH2 can be activated by selecting the functions A-B-C-D and
made to correspond with the transmitter channels CHA-CHB-CHC-CHD by setting the
jumpers situated on the circuit board (see fig.4).
TRANSMITTERS (fig. 6, 7)
In the transmitters each key corresponds to a different channel, with the sole
exception of the two key transmitters where it is possible to have the same chan-
nel for both keys. (single-channel operation).
For double-channel operation which can be obtained using the second key, set
the two-way DIP switch, located separately from the nine-way user code DIP
switch on the printed circuit board. Once the transmitter's functions have been
programmed or recognized, make sure that every STRIP in the outdoor receiver
(which carries the relay) corresponds to the desired function.
PROGRAMMING THE TRANSMITTER USER CODE
The transmitters and receivers are supplied with a block of 3-way dip-switches with
which to program the digital codes for each system. Programming can be carried
out more than once, even after the installation, thus ensuring the total secrecy of the
user code. To ensure an exact match between the transmitter and receiver codes
when programming the 2 and 4 key transmitters coupled with receivers with up to
4 channels remember to set the same code in both the receiver and the transmit-
ter using all the 9 available DIPS (19683 possible combinations). It is important to
remember that the receivers can only respond to one command at a time.
IT FOLLOWS THEREFORE THAT MULTIPLE FUNCTIONS CANNOT BE USED
CONTEMPORANEOUSLY.
TECHNICAL SPECIFICATIONS
Reception frequency
Attention: The transmission frequency of these products varies according to the approved
frequency and eventual personalisation in the country of destination
Country
Frequency
Italy
29,875 MHz
Europe
27,195 MHz
USA
27,195 MHz
RECEIVER
- local oscillation frequency tolerance ..................30 p.p.m. from -10° to +55°C
- intermediate frequency ........................................................................ 455 kHz
- antenna impedance in input ......................................................................50 Ω
- sensibility (fine signal) ............................................................................. 0.5 µV
- local oscillation emission ...................................................<-70dBm (<100pW)
- power supply ...............................................................................12-24V ac/dc
- maximum power consumption at rest .................................................... 40 mA
- maximum power consumption with activated relay ............................... 66 mA
- maximum commutable power at the relay:
load dc ...................................................................................................... 24W
load ac ..................................................................................................... 60VA
maximum voltage ............................................................................ 30V ac/dc
- excitation delay ......................................................................................150 ms
- dropout delay.........................................................................................150 ms
TRANSMITTERS
- carrier frequency tolerance ................................30 p.p.m. from -10° to + 55°C
- band width .................................................................................10 kHz/± 5kHz
- apparent radiated power ......................................... -10...-7dBm (100-200µW)
- apparent power harmonic products ..................................... <-64 dBm (<1nW)
- power output adjacent channel (± 10 kHz) ........................ <-37 dBm (<0.2µW)
- modulation ...........................................................................................AM/ASK
- signal modulation ................................................................... PCM, 1.3 ms/bit
- power supply ...................................................................................12V ± 10%
- maximum power consumption ............................................................. <38 mA
- operating temperature range ....................................................... - 20... +70°C
- relative humidity ......................................................................................< 95%
SERIES
MODEL
AM
13-12-2006
Antenna
ANQ730
ANQ727
ANQ727
DATE
Publicidad
