Publicidad
Idiomas disponibles
Idiomas disponibles
Before using your new Steren´s product, please read this instruction
manual to prevent any damage.
The instructions of this manual are for reference about the product. There may
be differences due to updates.
Please check our web site (www.steren.com) to obtain the latest version of the
instruction manual.
• Do not try to open the device, may cause damages and warranty will be void.
• Do not expose to extreme temperatures.
• Do not expose the device or accessories to dust, smoke or steam.
• Do not use solvents or other chemicals to clean the exterior of the device.
• Make sure the positive (+) and negative (-) ends of the batteries are inserted in the
correct directions.
• Old and new or different types of batteries should not be combined.
The chime has a pyrometric motion sensor, which transmits a wireless signal to the
chime in three modes: visual, acoustic or both (each mode can be selected easily
through a switch). It is perfect for small business, or stores.
Manufactured in high resistant ABS plastic, the on / off can be located in the sensor
and the chime can be adjusted in volume and tone. The sensor is powered by three
AAA batteries (not included), or by 3V 300mA power converter (not included), the
chime with two AA batteries.
• Wall or ceiling installation
• Luminous or acoustic indicator
• Range:
• Sensor detection: up to 7 m
• Signal transmission: up to 50 m
Sensor
1. Battery compartment
2. Motion detector
3 On/off switch
Receiver
1. Battery compartment
2. LED
3. Speaker
4. Mode switch
5. Volume
6. Melody selector
7. Pairing button
1. Select the sensor installation place. Remember that the motion detection range is
7 meters.
2. Mark the points where you must drill.
3. Make the necessary holes.
4. Set the base of the sensor using the included screws
and wall plugs.
1. Place 3 AAA batteries
in the sensor of movement
and 2 AA at the receiver.
2. Turn on the sensor by pressing the power button.
3 Use the switch on the receiver to select the operation
mode. The modes are: only light, only sound or light and
sound.
4. Select the volume by pressing the corresponding button. There are
three levels: low, medium and high.
5. You can change the melody by pressing the selector button.
6. To stop detection, simply press the power button on the sensor.
Note: If you need to pair another sensor with the receiver, turn on the sensor and press
pairing button on the back of the receiver. It will automatically search for available
sensors and pair with them.
Sensor power input:
4.5 V- - - (3xAAA)
3 V- - - 300mA (with power converter)
Chime power input:
3 V- - - (2xAA)
Consumption:
0.9 kWh/year
Stand-by power consumption:
0.04 kWh/year
Transmission frequency:
433.05-434.79 MHz
Product design and specifications are subject to change without notice.
Product: Wireless chime with motion sensor
Part number: ALA-035
Brand: Steren
This Steren product is warranted under normal usage against defects in workmanship and materials to the original purchaser for one year from
the date of purchase.
1.- This warranty card with all the required information, invoice or purchase ticket, product box or package, and product, must be presented when
warranty service is required.
2.- If the product stills on the warranty time, the company will repair it free of charge.
3.- The repairing time will not exceed 30 natural days, from the day the claim was received.
4.- Steren sell parts, components, consumables and accessories to customer, as well as warranty service, at any of the addresses mentioned later.
THIS WARRANTY IS VOID IN THE NEXT CASES:
If the product has been damaged by an accident, acts of God, mishandling, leaky batteries, failure to follow enclosed instructions, improper repair by
unauthorized personnel, improper safe keeping, among others.
a) The consumer can also claim the warranty service in the purchase establishment.
b) If you lose the warranty card, we can reissue it, if you show the invoice or purchase ticket.
RETAILER INFORMATION
Name of the retailer ____________________________________
Address _____________________________________________
Product ______________________________________________
Brand _______________________________________________
Serial number _________________________________________
Date of delivery _______________________________________
In case your product fails or have questions, please contact your nearest dealer. If you are in Mexico, please give a call to our Call Center.
5. Place the sensor at the base.
5. Orient the sensor so that it detects
movement in the area you need.
6. Place the receiver less than 50 metres away
from the sensor.
ON/OFF
WARRANTY
CONDITIONS
01 800 500 9000
Publicidad
