Página 3
Introduction Congratulations ! You are about to install and use a high-end equipment that will play a central role in the energy management of your battery-based system. The xtender is an smart battery inverter/charger with advanced functions. This xtender has been designed, manufactured, assembled and tested in our factory in Switzerland.
Studer disclaims all responsibility and liability for damage, costs or losses resulting from an installation that does not comply with the instructions, a faulty operation or inadequate maintenance. The use of studer equipment is in any case under the responsibility of the customer.
Página 5
Compatible with : rcc 02/03 xtender Configuration, display, datalogger Battery inverter/charger vario ECF 01 Solar charge controller Cooling fan xcom CAN Advanced battery processor (lead-acid) Communication with lithium BMS 232i 485i xcom LAN/GSM xcom 232i/CAN/485i Remote monitoring (Portal & App) Communication bridges (openstuder) bts 01 arm 02...
Mounting and installation Storage and content 60°C -20°C Mounting place The batteries should only be installed by qualified personnel.
Página 7
Fixing and dimensions 84mm min. 200mm min. 50mm min. 200mm 8.2 – 9.3kg 205mm 120mm...
Página 8
Wiring L1 L2 L3 Jumpers 2’ Bus termination Temperature sensor bts 01 / auxiliary contacts remote module arm 02 Communication • 1x RJ 11 black flat cable Remote control rcm 10 • 2x RJ 45 black flat cable : • 1x RJ 11 black flat cable rcc 02/03 / multi-units : xtender, vt, vs, bsp, xcom The device must be installed in accordance with local standards and regulations in force.
Página 9
Battery connection BAT+, M6 BAT-, M6 • 25mm cable M6, 4Nm xts 1200-24 xts 900-12 AC out connection • 16mm cable M6, 4Nm xts 1400-48 • Up to 3x4mm cable Protection device (battery side)* Protection device to protect cables • 100A xts 900-12 Up to 20Aac, circuit breaker type B •...
Página 10
Multi units and power up Up to 9 Xtenders in the same communication bus...
Display Display system Stop on – AC out present 230V / 120V ac acoustic blink – standby, load search warning on – the device is on blink – temporarily stopped due to a fault (Auto restart) or idle mode by master unit in multi units on –...
Configuring the xtender rcc 02/03 xtender xtender setting con guration assistant L1 1 0 Vac 231 Vac 0 Aac 0.03 kW 27.7 Vdc -2 Adc Displaying Configurating parameters real time user Basic settings information Battery management and cycle Inverter AC in and transfer Auxiliary contacs 1&2 System Multi xtender system...
Página 13
Multi units 3 phase and parallel combination L1 L2 L3 Automatic detection and configuration for 3 phase and multi unit system Solar priority for self comsumption In combination with a vario Automatic start generator & self consumption configuration See FAQ section ! variotrack, variostring...
Technical data IP 54 Protection Class I 900-12 1200-24 1400-48 Batt norminal voltage 12Vdc 24Vdc 48Vdc Batt charge current 35Adc 25Adc 12Adc Batt min-max voltage 9.5-17Vdc 19-34Vdc 38-68Vdc AC input 230V (150-265V) voltage *120V (50-140V) AC input max current Continuos Power 650**/500VA 800**/650VA 900**/750VA...
Página 15
Maintenance and recycling Maintenance and recycling Except for the periodic check of the connections (tightening, general condition), the xtender does not require any particular maintenance. To dispose of this product, please use the service for the collection of electrical waste and observe all obligations in force in the place of purchase.