VERTO 52G219 Instrucciones De Uso página 11

CONSTRUCTION AND USE
Table saw is designed for cutting wood and wood-like materials. Do
not use the saw for cutting firewood. Attempts to use the table saw
for purposes other than specified will be considered an improper
use. Use the table saw only with appropriate cutting blades with
teeth with solid carbide inserts. Range of use covers repair and
building works, and any work from the range of individual, amateur
activities (tinkering).
Use the tool according to its purpose only.
DESCRIPTION OF DRAWING PAGES
Below enumeration refers to the device elements depicted on the
drawing pages of this manual.
1. Angle bar
2. Rip fence
3. Cutting blade shield
4. Fixing knob for cutting blade shield
5. Work table
6. Locking knob for cutting blade tilt
7. Switch
8. Fixing knob for rip fence
9. Dust extraction outlet
10. Cover 11.Riving knife 12.Cutting blade
11. Work table insert
*Differences may appear between the product and drawing.
MEANING OF SYMBOLS
WARNING
EQUIPMENT AND ACCESSORIES
1. Rip fence 1 pce
2. Screw + washer 2 sets
3. Angle bar 1 pce
4. Push stick 1 pce
5. Ring spanner 2 pcs
PREPARATION FOR OPERATION
SAW INSTALLATION ON A WORKSHOP BENCH
It is recommended to firmly fix the table saw to a workbench with
the use of mount holes designed for such purpose. They are located
on the table saw base and guarantee safe operation and eliminate
risk of unwanted machine shifts during operation. Make sure the
package is removed from
INSTALLATION OF CUTTING BLADE SHIELD
•Put cutting blade shield (3) on the riving knife (11).
•Put the fixing knob fro cutting blade shield (4) into hole in the cutting
blade shield (3) and the riving knife (11) and tighten the knob.
•You can remove the cutting blade shield following above procedure
in reverse sequence.
Knob for locking the cutting blade shield should be tightened,
so the cutting blade shield lifts as the material is fed towards
the cutting blade and returns to default position after the
cutting is finished.
DUST EXTRACTION
Table saw is equipped with dust extraction outlet (9) which allows
sucking off sawdust emerging while cutting. Use appropriate
vacuum suction devices or industrial vacuum cleaners for this
purpose.
INSTALLATION OF RIP FENCE (HEIGHT OF REACTION)
Rip fence can be installed on either side of the work table.
•Install fixing knobs for rip fence (8) and washer for the rip fence (2).
•Slide the rip fence (2) into slot in the work table (5).
•Set required cutting width using scales located on the work table
top (5).
•Tighten fixing knobs for the rip fence (8).
underneath of the motor.
The rip fence (2) has two guiding surfaces (upper and lower setting
edge). Depending on thickness of the material to cut, install the rip
fence properly (fig. A).
•Loosen the fixing knobs for rip fence (8) and slide the rip fence (2)
out of the slots in the work table (5).
•Turn over the rip fence (5) by 1800 and attach it back to the work
table (5).
SETTING THE RIVING KNIFE
Disconnect the tool from power supply.
•Remove the cutting blade shield (3) and the work table insert (13)
by undoing the fixing screws.
•Loosen screws (a) fixing the riving knife (11) (fig. B).
•Set the riving knife (11) so the distance from the cutting blade (12)
is between 3 – 5 mm (riving knife should be exactly in line with the
cutting blade) (fig. C).
•Tighten screws for riving knife locking (a), install table top insert
(13) and cutting blade shield (3).
Check position of the riving knife after each replacement of the
cutting blade.
OPERATION / SETTINGS
Ensure the table saw is disconnected from power supply
network before starting any adjustments. To ensure safe,
precise and efficient table saw operation, proceed with all
adjustment procedures as a whole.
After finishing all the setting and adjustment procedures
ensure that all adjustment keys are collected. Check that all
threaded joining elements are properly tightened. When
making adjustments ensure that all external parts work
properly and are in good condition. Any worn out or damaged
part must be replaced by qualified personnel before starting to
use the table saw.
SWITCHING ON / SWITCHING OFF
The mains voltage must match the voltage on the rating
plate of the saw.
Switch on the table saw only when cutting blade is away from
the material that is to be cut.
Switching on
• Press the switch button "I" (2) (fig. D). Switching off
• Press the switch button "O" (2).
RIPPING
Ripping is cutting the material to desired width along its whole
length.
• Set the rip fence (2) to appropriate cutting width.
• Switch the table saw on and wait until cutting blade reaches its full
rotational speed.
• Press the material against the ripping fence (2) and move towards
cutting blade to the end of the riving knife (11) (use the push stick
when close to the cutting blade).
• Leave the cut material on the work table until the cutting blade
stops completely.
Make a try cut after each adjustment to ensure the new setting
is correct. When making a cut stand to the side of line of
cutting.
BEVEL CUTTING
When making a bevel cut, always use the rip fence.
• Loosen locking knobs for cutting blade tilt (6) located on both sides
of the saw.
• Overcome the spring resistance and press the motor body to set
the cutting blade (12) at desired angle (fig. E).
• You can read out the current angle using the scale (b) and the
indicator (c) (fig. F).
• Tighten the locking knobs for cutting blade tilt (6).
• Set the rip fence (2) to required width of cutting.
• Switch on the table saw and make a cut.
10