Chamberlain CLULP1 El Manual Del Propietario

CARTON INVENTORY
Anchor
Screw 6ABX1-1/4"
120 Vac Power Adapter
INSTALLATION
1. Open your garage door and park your vehicle outside of garage.
2. Determine the mounting location on the ceiling and fasten the
parking assist using screw and anchor (Figure 1).
3. For installation on a Chamberlain garage door opener:
Locate the quick connect terminals on your motor head.
Temporarily remove the wires for the safety reversing sensors
(see your owner's manual for the location of the quick connect
terminals.). The power adapter will not be needed, discard it.
For all other installations (power adapter required):
Locate the nearest 120 Vac power outlet to the parking assist(s).
Route wires from parking assist(s) to outlet. The power adapter
is intended to be correctly oriented in a vertical or floor
mount position.
4. Stripping the wires prior to installation:
Installing one parking assist: Separate white and white/black
wires and strip 7/16" (11 mm) of insulation from parking assist
wires.
Installing two parking assists: Cut 6" (15 cm) of wires from the
end of one set of parking assist wires for use as connection
wires. Separate white and white/black wires and strip 7/16"
(11 mm) of insulation from both ends of connection wire.
5. Connect the wires:
Installing one parking assist (Chamberlain installation): Twist
like colored wires for parking assist and safety reversing sensors
together. Insert twisted wires into quick-connect holes: white to
white and white/black to grey* (Figure 2A).
Installing one parking assist (all other installations): Connect
wires from parking assist to power adapter as shown (Figure 2B).
Plug power adapter into 120 Vac outlet.
Installing two parking assists (Chamberlain installation):
Separate white and white/black wires and strip 7/16" (11 mm) of
insulation from the end of parking assist wires. Twist like colored
wires for parking assists, safety reversing sensors and
connection wire together. Secure with wire nut. Insert connection
wires into quick-connect holes: white to white and white/black to
grey* (Figure 3A).
Installing two parking assists (all other installations): Twist
like colored wires from parking assists and connection wires
together. Secure with wire nut and attach connection wires to
power adapter as shown (Figure 3B). Plug power adapter into
120 Vac outlet.
* Please refer to your garage door opener owner's manual for
proper wire installation.
Wire Nut (2)
Parking Assist
®
Chamberlain Laser Garage Parking Assist
To avoid eye INJURY or damage to product:
• NEVER point the laser at anyone.
• NEVER look directly into the laser beam.
• NEVER disassemble the laser.
• The parking assist is NOT a substitute for safe parking practices.
• Use of controls or adjustments, or the performance or procedures
other than specified can result in hazardous radiation exposure.
• ONLY for use on Chamberlain manufactured garage door openers.
This Class B digital
apparatus complies
with ICES-003.
Figure 1
Figure 2A
Safety Reversing
Sensor Wires
Figure 2B
Figure 3A
Safety
Reversing
Sensor Wires
Figure 3B
Model CLULP1
WARNING
CAUTION
CAUTION
ATTENTION
LASER RADIATION
DO NOT STARE INTO BEAM
RAYONNEMENT LASER
NE PAS REGARDER DIRECTEMENT
LE RAYONNEMENT LASER
Maximum power output: < 1mW @ 635 - 670nm
Puissance de sortie maximum: < 1mW @ 635 - 670nm
CLASS II LASER PRODUCT
APPAREIL AU LASER DE CLASSE II
Insert into appropriate terminals
Parking Assist Wires
Red White Grey
White (-)
Parking Assist Wires
White/Black (+)
120 Vac Power Adapter
Insert Into Appropriate Terminals
Wire Nut
White
Connection
Connection
Wire
Wire
Parking Assist
Wires
Red White
Parking Assist
Wires
White (-)
Wire
White/Black (+)
Nuts
120 Vac Power Adapter
Owner's Manual
White/Black
Connection
Wire
Grey