Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
Hitch Shown In Proper Position
Equipment Required:
Fastener Kit: K24659
Wrenches: 7/8"
Drill Bits: 1/2"
1
Qty. (4)
CARRIAGE BOLT 1/2"-13 X 1-3/4"
2
Qty. (1)
BLOCK 1/4 X 2-1/2 X 6
3
Qty. (2)
LOCK WASHER – 1/2"
1. ENLARGE EXISTING HOLES IN BUMPER TO 1/2".
2. REMOVE SPARE TIRE AND TRUNK PAN RUBBER PLUGS.
3. RAISE HITCH INTO POSITION AND ATTACH WITH FASTENERS AS SHOWN ABOVE.
4. SEAL HOLES IN TRUNK PAN TO PREVENT INTRUSION OF EXHAUST FUMES AND WATER.
5. REINSTALL SPARE TIRE.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
z
2006 Cequent Towing Products
Installation Instructions
BUICK CENTURY, OLDSMOBILE INTRIGUE,
PONTIAC GRAND PRIX
Drawbar Kit:
Drawbar must be used in the
RISE position only.
1
2
3
4
TRUNK PAN
Tighten all 1/2 fasteners with torque wrench to 75 Lb.-Ft. (102 N*M)
3592
Do Not Exceed Lower of Towing Vehicle
2000 LB Max Gross Trailer Weight
200 LB Max Tongue Weight
Wiring Access Location: PC3, PC4
1
6
5
4
REMOVE
RUBBER PLUG
4
Qty. (4)
NUT 1/2"-13
5
Qty. (2)
CONICAL TOOTHED WASHER
6
Qty. (2)
BLOCK 1/4" X 1-1/2" X 2"
Sheet 1 of 3
N24659
Part Numbers:
N24659
N77109
N60833
Manufacturer's Rating or
04-04-06
BUMPER
ENLARGE
EXISTING
HOLES
Rev. B
Publicidad
Manuales relacionados para Cequent Towing Products N24659
Resumen de contenidos para Cequent Towing Products N24659
- Página 1 Do not cut access or attachment holes with a torch. This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. Sheet 1 of 3 N24659 04-04-06 Rev. B 2006 Cequent Towing Products...
- Página 2 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. 2006 Cequent Towing Products Feuille 2 de 3 N24659 04-04-06 Rev.
- Página 3 Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York, V.E.S.C. Regulación V-5 y SAE J684 2006 Cequent Towing Products Hoja 3 de 3 N24659 04-04-06 Rev.