Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
Tie down bracket
Hitch Shown In Proper Position
Equipment Required: Small Flat Head Screwdriver, Lubricant
or Soapy water
Fastener Kit: 24828F
Wrenches: 12mm, 13mm, 9/16", 11/16", & 3/4" (2)
Remove
existing M8
bolts from end
of each frame
rail.
1 1 1 1
Qty. (2)
Hex bolt M8 X 1.25 X 35 CL9.8
2 2 2 2
Qty. (2)
Hex bolt 1/2-13 X 2.00 GR5
3 3 3 3
Qty. (4)
Spacer
4 4 4 4
Qty. (2)
Conical washer 1/2"
1.
Remove appearance panel which covers the trunk pan. Remove the (7) plastic rivets that fasten the fascia tabs to the vehicle.
Note: Remove the center of the rivet with a screwdriver. Return appearance panel and fasteners to vehicle owner.
2.
Remove existing M8 bolts (2) from end of each frame rail. Return fasteners to owner. See Figure 2.
3.
Lower exhaust system at the rubber isolator. Note: Spraying a lubricant or soapy water on the metal hanger rod and the rubber
isolator helps removal.
4.
Raise hitch into position over the exhaust.
5.
Install fasteners as shown above. See Figure 1.
6.
Tighten all fasteners to called-out torque specification
7.
Raise exhaust system back into position.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
z
2008, 2015 Cequent Towing Products – Printed in Mexico
Installation Instructions
Fascia
(Sold separately)
Drawbar Kit:
3593
Drawbar must be used in
the Rise position only.
Note: Fasteners typical both sides
Existing
weldnut
Figure 2.
Tighten all M8 CL9.8 fasteners with torque wrench to 17 Lb.-Ft. (23 N*M)
Tighten all 3/8-16 GR5 fasteners with torque wrench to 30 Lb.-Ft. (41 N*M)
Tighten all 1/2-13 GR5 fasteners with torque wrench to 75 Lb.-Ft. (102 N*M)
Scion xD
Do Not Exceed Lower of Towing Vehicle
2000 LB (908 Kg) Max Gross Trailer Weight
200 LB (90.8 Kg) Max Tongue Weight
Wiring Access Location:
3 7
Tie down
bracket
1
6 7
2
5 5 5 5
Qty. (2)
Hex nut 1/2-13
6 6 6 6
Qty. (2)
Hex bolt 3/8-16 X 1.75 GR5
7 7 7 7
Qty. (4)
Conical washer 3/8"
8 8 8 8
Qty. (2)
Hex nut 3/8-16
Sheet 1 of 3
Manufacturer's Rating or
8
5
3 4
Figure 1.
24828N
10-8-15
Form F206 Rev A 5605
Part Numbers:
24828
60214
77200
Exhaust not
shown for
clarity
Rev. B
Publicidad
Manuales relacionados para Cequent Towing Products 24828
Resumen de contenidos para Cequent Towing Products 24828
- Página 1 This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. 2008, 2015 Cequent Towing Products – Printed in Mexico Sheet 1 of 3 24828N 10-8-15 Rev.
- Página 2 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. Feuille 2 de 3 24828N 10-8-15 Rev. B 2008, 2015 Cequent Towing Products - Imprimé au Mexique Form: F205 Rev A 5-6-05...
- Página 3 Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York. V.E.S.C. Regulación V-5 y SAE J684 Hoja 3 de 3 24828N 10-8-15 Rev. B 2008, 2015 Cequent Towing Products - Impreso en México Form: F205 Rev A 5-6-05...