Control Features; Technical Specifications - JBL Reference Serie Guia Del Usuario

Symptom when used with Possible Problem
Bluetooth transceiver
Pairing
Audio device does not pair with Audio device does not support
headphones. A2DP profiles.
Headphone system is not
powered "On".
Headphone system is still paired
to Bluetooth transceiver.
iPod battery is low.

Technical Specifications

Manufacturer: Harman Consumer Group, Inc.
Model Name: JBL Reference Series 610
Available in: White/Black with Chrome
Features Sensitivity: 96dB SPL/mW @ 1kHz
Input Requirement, iPod Dongle: iPod Dongle connected to iPod models 4th generation and above
Input Requirement, iPod Dongle: Bluetooth A2DP and AVRCP profile streaming
Drivers: Two 40mm neodymium drivers
Input Power: 2 x 50mW maximum power
Frequency Response: 20Hz – 20kHz (–10dB)
Dimensions: Diameter – 102mm, hardwire audio cable – 1.75m
Weight: 212g without cord
Input Impedance: 32 ohms
Wireless Compatibility: Most Bluetooth-enabled audio devices with A2DP and AVRCP profiles
Hardwired Compatibility: Audio devices with 3.5mm mini audio jack connection
Battery Usage: 8–10 hrs continuous play
Solution Note
Audio device is not compatible.
Verify with manufacturer.
Press down on power button. Blue LED should go from solid
to three consecutive, fast blinks,
indicating that it's ready to be
"discovered" by transceiver or
other audio source.
Disconnect transceiver from If LED has intermittent, slow
iPod and turn headphone power blinks on both dongle and
"Off", then back "On". headphones, both devices are
connected. If you wish to
re-pair, please follow initial
pairing instruction.
Charge headphones by following If blue LED on headphones
the battery charging directions in
continues to blink rapidly after
this User Guide. headphone system has paired,
it is indicating a low battery. A
monotone will also be sounded
every 5 seconds for low bat-
tery alert.
Symptom when used with Possible Problem
Bluetooth transceiver

Control Features

Headphone controls do not work Audio device is not compatible
with Bluetooth audio device. with AVRCP profile.
Headphone controls have Audio device does not recognize
limited operation. some control features.
Sound Quality
No sound from headphones. Headphone system has lost the
link with the audio device.
If using audio cable, connection
at mini USB or 3.5mm audio
inlet end may not be connected
properly.
Sound drops in and out. Moving out of transmission
range.
Audio device is dropping
transmission.
Headphone battery is low.
Distortion (static, crackling or Noise may be caused by interfer-
hissing sounds). ence from a monitor, cell phone
or other transmitting device.
If using audio cable, headphone
system may be overdriven by an
amplified audio source.
6
Solution Note
Audio device is not compatible.
Verify with manufacturer.
Contact your audio device manu- Because of the large variation in
facturer to check limitations. design, the control features may
be limited due to restrictions on
your audio device.
Follow your audio device's user
guide instructions to re-pair the
Bluetooth connection.
Make sure connectors are mat-
ing correctly to your headphone
and audio device. Make sure
headphone power is "Off".
Move closer to audio device or
change position.
Contact audio device manufac-
turer for guidance.
Charge headphones by following If blue LED on headphones
the battery charging directions in continues to blink rapidly after
this User Guide. headphone system has paired,
it is indicating a low battery. A
monotone will also be sounded
every 5 seconds for low bat-
tery alert.
Turn monitor off to see
whether noise is eliminated. Use
headphones further away from
monitor.
Ensure that the JBL Reference
Series 610 is connected to an
appropriate source device. Make
sure cables are inserted snugly
into receptacles. Reduce volume
on the audio source.