Fitting Shredder Upper Section With Cutting Unit And Motor Unit (03); Fitting The Hopper (03); Start-Up; Operation - AL-KO Easy Crush MH 2810 Manual Del Usuario

Start-up

4. Slide the medium 8x20x1.5 washer (02/6) on-
to the thread and secure the transport wheel
using an M8 nut (02/7).
5. Finally, press the wheel cap (02/8) onto the
transport wheel (02/5).
6. Fit the opposite transport wheel in the same
sequence.
5.2 Fitting shredder upper section with
cutting unit and motor unit (03)
1. Lift the shredder upper section onto the base
and secure it using M5x30 bolts (03/1) and
washers 5x10x1.
5.3

Fitting the hopper (03)

1. Place the hopper onto the shredder upper
section and secure it using ST 4.2x18 bolts
(03/2).
6 START-UP
■
Comply with working time regulations in force
in your country.
■
Do not route the extension lead over the hop-
per or under the discharge opening.
■
The shredder can only be started when the
collector box is locked.
■
Check the hopper and shredder upper sec-
tion (MH 2810) or hopper (LH 2810) for ob-
structions before starting the machine.
■
LH 2810: The counterplate (07/2) is factory-
calibrated and must not be adjusted during
initial start-up.
■
Do not use the shredder if you are:
■
Tired
■
Unwell
■
Under the influence of alcohol, medicines
and drugs
DANGER! Danger of injury from dam-
aged components! Damaged components can
lead to serious and even fatal injuries!
■
Before putting into operation, carry out a vi-
sual inspection and check the components
for function.
WARNING! Risk of injury due to negli-
gence! Negligence in handling the machine can
result in serious injuries!
■
Only use the shredder on firm, level ground
and in a stable position. Do not tilt or incline
the machine during operation.
442981_b

7 OPERATION

WARNING! Danger of serious injury!
There is a risk of serious injuries for children, per-
sons with impaired physical, sensory or mental
abilities, persons with insufficient knowledge and
experience and persons who are not familiar with
the operating instructions.
■
Never permit the above persons to use the
machine.
■
Always observe the local regulations con-
cerning the age limit for users.
7.1

Connecting the mains plug (04/05)

1. Push down the cable lock (04/1) and insert
the extension lead (05/1) into the socket of
the shredder.
2. Check that the extension lead is connected
securely.
3. Then connect the extension lead to the mains
voltage.
7.2

Switching on the motor (06)

MH 2810
1. Press the ON switch (06/1).
LH 2810
Normal operation:
1. Turn the direction of rotation switch (06/4) of
the cutting drum to the left (06/6).
2. Then press the ON switch (06/1).
3. The material to be shredded is pulled in.
Reverse:
See see chapter 7.4 "Clearing a cutting disk/cut-
ting drum blockage", page 23.
7.3

Switching off the motor (06)

1. Press the OFF switch (06/2) to switch the
motor off.
CAUTION! Damage to the machine due to
improper operation! Incorrect handling can re-
sult in machine damage!
■
Only feed material to be shredded after the
machine has been switched on.
■
Do not feed material to be shredded after the
machine has been switched off.
7.4 Clearing a cutting disk/cutting drum
blockage
Clearing a cutting disk blockage (MH 2810)
(09/10 )
1. Switch off the shredder.
23