Ocultar thumbs Ver también para H60K-51D-CH:

Publicidad

Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

KITCHEN FAUCET
H60K-51D-CH – Polished chrome finish with pull-out spray
H60K-51D-BN – Brushed nickel finish with pull-out spray
H60K-51D-ORB – Oil rubbed bronze finish with pull-out spray
PACKAGE AND HARDWARE CONTENTS
PART
DESCRIPTION
A
Faucet assembly
B
C
Mounting bolt
D
Mounting nut
E
Rubber washer
F
Lock nut
G
H
SAFETY INFORMATION
Please read and understand this entire manual before attempting to
assemble, operate or install the product.
WARNING
• Protect your eyes with safety glasses when cutting or soldering water supply
lines.
PREPARATION
Before beginning assembly of product, make sure all parts are present. Compare
parts with package contents list and hardware contents. If any part is missing or
damaged, do not attempt to assemble the product.
Contact customer service for replacement parts.
Estimated Assembly Time: 30 minutes
Tools Required for Assembly (not included): Adjustable Wrench, thread sealant
tape, Silicone
Need Help? Please call our toll-free line at (877) 319-3757 (8 am to 5 pm CST) for additional assistance or service.
Homewerks Worldwide, LLC • Lake Bluff, IL 60044 • www.homewerksww.com
QUANTITY
Gasket
Screw
Collar
1
1
2
2
A
1
1
2
1
CAUTION
• If you solder the joints during installation, the seats, cartridges, and washers
must be removed before using a flame or the warranty will be voided on
these parts.
• Cover the drain to avoid losing parts.
Installations may vary depending on how the previous faucet was
installed. Supplies necessary for the installation of the faucet are not
all included; however, they are available wherever plumbing supplies
are sold.
Prior to beginning installation, turn off the hot and cold water lines, then turn
on the old faucet to release built-up pressure. When installing the new faucet,
hand tighten the connector nuts. DO NOT OVERTIGHTEN. Connections
that are too tight will reduce the integrity of the system.
NSF/ANSI 6 1
B
C
E
F
D
G
H
ADA
04-27-2018

Publicidad

Tabla de contenido
loading

Resumen de contenidos para Home2O H60K-51D-CH

  • Página 1 KITCHEN FAUCET H60K-51D-CH – Polished chrome finish with pull-out spray H60K-51D-BN – Brushed nickel finish with pull-out spray H60K-51D-ORB – Oil rubbed bronze finish with pull-out spray NSF/ANSI 6 1 PACKAGE AND HARDWARE CONTENTS PART DESCRIPTION QUANTITY Faucet assembly Gasket...
  • Página 2: Product Specifications

    PRODUCT SPECIFICATIONS SPECIFICATIONS SPECIFICATIONS Max. Flow Rate: 1.8 GPM (6.814 LPM) at 60 PSI Ball control cartridge ASME A112.18.1/CSA B125 Manufactured to include no more than 0.25% weighted average lead content on wetted surfaces NSF 61-9 Polished chrome, brushed nickel or oil rubbed bronze finish Total weight of item: 3.90 lbs.
  • Página 3: Troubleshooting

    ASSEMBLY INSTRUCTIONS 9. Pull sprayer hose out of spout and 10. Attach spray wand, hand tighten hold into sink. Flush both water lines and turn water on. CHECK ALL by turning handle to a full mixed CONNECTIONS FOR LEAKS. position, allowing water to run for one minute.
  • Página 4: Replacement Parts

    REPLACEMENT PARTS For replacement parts, call our customer service department at (877) 319-3757, 8 a.m. - 5 p.m., CST, Monday - Friday. PART DESCRIPTION PART # PART # PART # H60K-51D-CH H60K-51D-BN H60K-51D-ORB Handle assembly RP03040CH RP03040BN RP03040ORB Retaining ring RP03041CH...
  • Página 5: Grifo De La Cocina

    GRIFO DE LA COCINA H60K-51D-CH - Acabado en cromo pulido con rociador extraíble H60K-51D-BN - Acabado de níquel cepillado con rociador extraíble H60K-51D-ORB - Acabado en bronce pulido con rociador extraíble NSF/ANSI 6 1 PAQUETE DE HARDWARE Y CONTENIDO PARTE DESCRIPCIÓN...
  • Página 6: Especificaciones Del Producto

    ESPECIFICACIONES DEL PRODUCTO ESPECIFICACIONES ESPECIFICACIONES Caudal de flujo máximo: 6,814 LPM (1,8 GPM) a 60 PSI Cartucho de control de bola ASME A112.18.1/CSA B125 Fabricado a incluir no más de 0,25% de contenido de plomo promedio ponderado en superficies mojadas NSF 61-9 Cromo pulido, níquel cepillado y acabado en bronce aceitado Peso total: 3.90 libras...
  • Página 7: Solución De Problemas

    INSTRUCCIONES DE MONTAJE 9. Jale la manguera del rociador fuera 10. Coloque la varilla de pulverización, del surtidor y sostenga en el apriete a mano y encender el agua fregadero. Enjuague ambas líneas de COMPRUEBE TODAS LAS agua girando la manija a una CONEXIONES PARA DETECTAR posición completamente mezclada, FUGAS.
  • Página 8: Lista De Repuestos

    Para piezas de repuesto, llame a nuestro departamento de servicio al cliente al (877) 319-3757, 8 a.m.-5 p.m. CST, Lunes - Viernes. PARTE DESCRIPCIÓN PARTE# PARTE# PARTE# H60K-51D-BN H60K-51D-ORB H60K-51D-CH Mango de montaje RP03040CH RP03040BN RP03040ORB Anillo de retención RP03041CH RP03041BN...

Este manual también es adecuado para:

H60k-51d-bnH60k-51d-orb

Tabla de contenido