Publicidad
DS-PD1-MC-WWS
EN50131-2-6:2008
Wireless Magnetic Contact
EN50131-5-3:2005+A1:2008
Security Grade (SG) 2
Environmental Class (EC) II
E N G L I S H
Diagram References
Installation Notes
It is recommended the contact is learned at the control panel. A signal strength
test should then be performed to make sure the most suitable location is chosen,
ensuring optimum wireless range.
Installation Surfaces
The contact can be mounted on typical building materials; such as wood, PVC,
brick or metal etc.
Programming Menus Required
1
WIRELESS DEVICE CONTROL (REGISTER WIRELESS DEVICE)
Register Locally
1. Make the security control panel enter the registration mode.
2. Register the detector: Hold the learnt key until the three LEDs flash
alternately. The green LED will flash 8 times if the registration is finished.
3. Communication Test: Release the TAMPER spring to trigger the alarm .
Note: The distance between the security control panel and the detector should
be less than 50 cm.
Initialize the Detector
1. Remove the battery to power the detector off.
2. 5s later, hold the registration key and reinstall the battery to power the
detector on at the same time to make the three LEDs start flashing
alternately. Release the registration key while the three LEDs flash once
together.
2
DIAGNOSTICS
Make sure the LED keeps green at the installation position when the detector is in
the signal strength mode before mounting.
Specification
Frequency
868MHz
Wireless
Modulation
2GFSK
Method
Fully encrypted rolling code
Type
3.0V CR123A
Battery
Threshold
2.5V +/- 5% at 25°C
Life
Up to 2 years
Colour and Casing
White. 2mm ABS
LEDs (Signal, Battery, Alarm,
Indication
Tamper)
Materials and Environment
Temperature
-10°C to 40°C (Certified)
Sensor:27 x 104 x 25mm.
Dimensions (H x W x D)
Magnet: 14 x 49 x 16mm
Magnet Detection Performance
Spacers available if required:
SPACER-WE and SPACERBROWN-WE
Battery Information
The batteries supplied have been chosen to provide long service life whilst, for
safety reasons, having limited output current.
The battery is protected on purchase by a piece of plastic that must be
removed for operation. When disposing of the product, the battery must be
removed and disposed of separately in accordance with the local regulations.
Product Warning Information
For electrical products sold within the European Community. At the end of the electrical products life, it
should not be disposed of with household waste. Please recycle where facilities exist. Check with your
Local Authority or retailer for recycling advice in your country.
To prevent possible damage to components, any static charge on your body needs to be eliminated
before touching the inside of the unit. This can be accomplished by touching some grounded/earthed
metallic conductor such as a radiator/pipework immediately before replacing the batteries.
E N G L I S H
Diagram References
Product Information
COPYRIGHT ©2018 Hangzhou Hikvision Digital Technology Co., Ltd.
ALL RIGHTS RESERVED.
Any and all information, including, among others, wordings, pictures, graphs are the
properties of Hangzhou Hikvision Digital Technology Co., Ltd. or its subsidiaries
(hereinafter referred to be "Hikvision"). This user manual (hereinafter referred to be "the
Manual") cannot be reproduced, changed, translated, or distributed, partially or wholly,
by any means, without the prior written permission of Hikvision. Unless otherwise
stipulated, Hikvision does not make any warranties, guarantees or representations,
express or implied, regarding to the Manual.
About this Manual
This Manual is applicable to the Axiom Security Control Panel Kit.
The Manual includes instructions for using and managing the product. Pictures, charts,
images and all other information hereinafter are for description and explanation only. The
information contained in the Manual is subject to change, without notice, due to firmware
updates or other reasons. Please find the latest version in the company website
(http://overseas.hikvision.com/en/).
Please use this user manual under the guidance of professionals.
Trademarks Acknowledgement and other Hikvision's trademarks and
logos are the properties of Hikvision in various jurisdictions. Other trademarks and logos
mentioned below are the properties of their respective owners.
2
2
Components
Control Panel x 1
Battery x 1
1
REGISTRATION
300s
No. 6.
Pan Head
Screw
10m
2 1
Magnetic Door Contact x 1
Screw x 4
Power Adapter x 1
< 50CM
5s
LEDs
LEDs
>10m
Detector x 1
Quick Start Guide x1
Publicidad
