Fitting Instructions; Getting Started; Charging The Battery; Checking The Battery Level - Stihl ADVANCE ProCOM Instrucciones De Mantenimiento

Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 42
• Do not store the helmet with the helmet attachment in stand-
by position. This causes stress on the helmet attachment.
• When the helmet is not in use, ensure that the ear cups are
left in parking position. This will decrease the stress on the
helmet attachment.

4. FITTING INSTRUCTIONS

4.1 ADVANCE ProCOM Headband Type
(G:1) Remove all hair under the earmuffs before putting
them on.
(G:2) Adjust the headband by extending the centre band
equally on both sides.
(G:3) Fit the earmuffs over your ears ensuring a tight fit
around your ears.
(G:4) Adjust the headband by sliding the headband up or
down to obtain a snug, comfortable fit.
(G:5) Ensure the earmuffs completely surround your ears.
Position the microphone close to your mouth.
(G:6) To remove the headset, ensure the earmuffs are in
the usage position and pull the earmuffs on both side to
remove the headset from your head.
4.2 ADVANCE ProCOM - with Adaptors for Function
Universal, ADVANCE X-Climb or ADVANCE Vent/X-Vent
(H:1) Remove all hair under the earmuffs before putting
them on.
(H:2) Place the helmet on your head with the earmuffs
in the stand-by position. Ensure the helmet is tight and
secure.
(H:3) Ensure the earmuffs completely cover your ears while
ensuring the helmet is on your head.
(H:4) Adjust the height of the earmuffs to ensure the
earmuffs completely surround your ears, giving a snug,
comfortable fit.
(H:5) Ensure that the earmuffs are firmly attached. Position
the microphone close to your mouth.
(H:6) To remove the helmet, ensure the earmuffs are in the
parking position and remove the helmet from your head.

5. GETTING STARTED

(See also Quick Start Guide)
5.1 Downloading STIHL Software
• ADVANCE ProCOM App
- Android: Google Play Store > ADVANCE ProCOM
- iOS: App Store > ADVANCE ProCOM
• STIHL Device Manager
The STIHL Device Manager allows you to upgrade
firmware and configure settings directly from your
PC. Download the STIHL Device Manager from
support.stihl.com.
• Firmware Upgrades
The headset supports firmware upgrades. You can upgrade
the firmware using the STIHL Device Manager. Please
visit support.stihl.com to check for the latest software
downloads.

5.2 Charging the Battery

WARNING
When charging the battery, use only a charger that is
approved and meets the requirements of the applicable
legislation in your country. Use of a non-approved charger
may cause fire, explosion, leakage, and other hazards
which may also reduce the life time or performance of the
battery.
You can charge the headset by connecting the supplied
USB power & data cable into a computer's USB port
or USB wall charger. You can use any standard USB-C
cable to charge the units. It takes about 2.5 hours to be
completely charged.
NOTE:
• Close the USB port after charging with a rubber cover
properly.
• The headset is compatible with 5 V/1000 mA input USB-
charged devices only.
• When charging the battery, the blinking yellow and green
LED will alternate intermittently.
• When charging a fully charged battery, the blinking green
LED will appear in two patterns.
5.3 Switching On and Off the Headset
To switch on the headset, press and hold the Multi-function
Button for 2 seconds. You will hear ascending beeps and a
voice notification, "Hello".
To switch off the headset, press and hold the Multi-function
Button for 2 seconds. You will hear descending beeps and
a voice notification, "Goodbye".
NOTE: When switching on the headset, the Mesh Intercom
is automatically activated.

5.4 Checking the Battery Level

You can check the battery level when switching the
headset on or off. The battery condition is indicated by the
LED in the left earmuff.
• Blinking in green = High, 70-100%. You will hear a voice
notification, "Battery level is high".
• Blinking slowly in yellow = Medium, 30-70%. You will hear a
voice notification, "Battery level is medium".
• Blinking fast in red = Low, 0-30%. You will hear a voice
notification, "Battery level is low".
17
GB

Publicidad

Tabla de contenido
loading

Tabla de contenido