Black and Decker BDCINF18 Manual Del Usuario página 7

This occurs when the unit is not operating.
To wake up the system, the user will need to push the
pressure mode / reset button (5) . At this time the LCD will
turn on and the inflator is ready for use.
Before switching your inflator on decided which power
u
source you will be using; 12V DC adapter, 230V AC plug
or a 20V MAX* battery pack.
To use the 12V DC adapter, or 20V MAX* battery pack
u
press the AC/DC power switch (1) located on the front of
the unit to DC.
If using the 12V DC cord, ,always fully extend the 12V DC
u
cord before each use.
Connect the 12V DC adapter 14 into your vehicles
u
12V DC accessory socket.
To use the 230V AC cord, press the AC/DC switch 1 located
on the front of the unit to AC.
If using the 230V AC cord 13 , always fully extend the
u
cord before each use.
Connect the 230V AC plug 13 into either a wall
u
outlet or an approapriate sized extension cord that
is plugged into a wall outlet.
To turn on high-volume
The high-volume hose is meant to be used for objects that
hold large amounts of air, such as air mattresses, rafts, and
swimming pool floats.
Note: The high-volume mode DOES NOT have an auto
shut-off feature.
Attach the high-volume hose (7) to the high volume pump
u
inflator connection (12) as described in the "High
volume hose" section.
Insert the high-volume hose (7) , or it's tapered nozzle (8)
u
into the object being inflated.
Press the high-volume side of the mode power switch (2) ,
u
indicated by the air mattress symbol.
To turn off, push the power switch to the center position.
u
To turn on high-pressure
The high-pressure hose is meant to be used for objects that
need more air pressure, such as tires and basketballs.
Remove the high-pressure hose (10) from the storage.
u
Attach a nozzle as described in the "Universal valve
u
adapter" section.
Insert the nozzle into the object being inflated.
u
Press the high-pressure side of the mode power switch
u
(2), indicated by the tire symbol.
To turn off, push the power switch to the center position.
u
Deflate using the high-volume hose (Fig. H)
Warning! Beware of objects being ejected. When deflating,
large amounts of air will exit the high volume pump inflator
connection (12) . Ensure the universal valve adapter is not
pointed at anyone or anything.
(Original instructions)
Remove the high-volume hose (7) from the storage
u
location.
Line up the hose end (23) with the high-volume pump
u
deflate connection (11) . Then, firmly slide in the hose so it
is securly in place.
Insert the hose, or it's tapered nozzle (8) into the object
u
being deflated.
Press the high-volume side of the mode power switch (2),
u
as shown in figure G, indicated by the air mattress symbol.
To turn off, push the power switch to the center position.
u
To remove the hose, twist the hose clockwise and slide
u
hose off.
Setting the automatic shut-off pressure
Note: The LCD will only show inflation pressures when the
inflator is being used. In both inflation and pump mode the
unit will show battery status.
To switch between the different units (psi, bar or kPa),
u
press the pressure mode button (5) until the required
units are displayed.
Press the - or + pressure setting buttons (4) until the
u
required pressure is displayed.
After 3 seconds the display will flash and return to a
u
reading of "0.0". This is normal.
Connect the universal valve adaptor and accessories,
u
if required, to the item to be inflated, making sure that
the lever of the valve adaptor is in the down position to
lock it in place.
To start the inflator press the mode power switch (2) ,
u
towards the side of the tire symbol.
When the item to be inflated has reached the preset
u
value the unit will automatically turn off. NOTE: You
may notice the actual pressure reading may drop after a
couple of seconds. This is normal.
To stop the inflator at any time, press the main power
u
button back to the center position.
Note: If the AC/DC power switch is turned off, all settings
will be lost and will need to be reentered. This is a safety
feature to prevent the risk of items over inflating.
Using the inflator as a pressure gauge
Connect the universal valve adaptor (9) to the item to be
u
checked.
Press the mode power switch (2) , on the side of the tyre
u
symbol.
The LCD will display the item's pressure.
u
After checking, press the mode power switch (2) back to
u
the center position and return the air hose to the storage
location.
ENGLISH
7