Westin 25-0770 Manual De Instrucciones

AUTOMOTIVE PRODUCTS, INC.
STEP BAR ASSEMBLIES
ENSAMBLES DE ESTRIBOS
MONTAGES DE MARCHE-PIEDS
25-0770
25-0775
ITEM QTY
1,2 2 STEP BAR, PASSENGER (1) AND DRIVER (2)
3 2 FRONT BRACKET
4,5 2 REAR BRACKET, PASSENGER (4) AND DRIVER (5)
6 4 REAR HOOK
7 8 1/2-13 X 1.75" HEX HEAD BOLT
8 10 1/2" FLAT WASHER
9 10 1/2" LOCK WASHER
10 2 M12-1.75 X 120MM HEX HEAD BOLT
1,2 2 ESTRIBOS, ACOMPAÑANTE
3 2 SOPORTE DELANTERAS
4,5 2 SOPORTE TRASERAS, ACOMPAÑANTE
6 4 GANCHOS TRASEROS
7 8 PERNOS CON CABEZA HEXAGONAL DE 1/2-13 X 1,75"
8 10 ARANDELAS PLANAS DE 1/2"
9 10 ARANDELAS DE PRESIÓN DE 1/2"
10 2 PERNOS CON CABEZA HEXAGONAL DE M12-1,75 X 120MM
1,2 2 MARCHE-PIEDS,
3 2 SUPPORTS AVANT
4,5 2 SUPPORTS ARRIERE,
6 4 CROCHET ARRIERE
7 8 BOULON A TETE HEXAGONALE DE 1/2-13 X 1,75 PO
8 10 RONDELLE PLATE 1/2 PO
9 10 RONDELLE A FREIM DE 1/2 PO
10 2 BOULONS A TETE HEXAGONALE M12-1,75 X 120MM
STEP 1.
Remove the contents from box and check for damage. Verify all parts are present. Read instructions
completely before beginning.
STEP 2.
Remove bolt from front body mounts located under cab of vehicle. Attach front bracket to body mount
as shown. Leave bolt loose to allow for positioning of step bar.
STEP 3.
Attach rear bracket to vehicle frame as shown.
covers the plastic inserts in frame. Position the rear hook over top edge of the frame using a 1/2-13 x
1.75" hex head bolt, 1/2" lock washer and 1/2" flat washer through the top hole in rear bracket and thread
into the nut on the rear hook. Hand tighten.
STEP 4.
Repeat Step 3 to install the other rear hook.
emergency brake cables are not binding on it. Hand tighten.
STEP 5.
Attach step bar to bracket using 1/2" fasteners. Make sure step bar and brackets are properly aligned
with vehicle and tighten fasteners. Tighten rear hooks gradually to keep rear bracket flat against truck
frame. Torque to 45 FT.LBS. Recommended torque value is 79 Ft. Lbs. for 12mm bolts and 64 Ft. Lbs. for
1/2" fasteners.
FINISH PROTECTION
Westin products have a high quality finish that must be cared for like any other exposed finish on the vehicle. Protect the finish with a non-abrasive automotive wax,
(e.g. Pure Carnauba) on a regular basis. The use of any soap, polish or wax that contains an abrasive is detrimental, as the compounds scratch the finish and
open it to corrosion.
INSTRUCTIONS-INSTRUCCIONES-CONSIGNES
APPLICATION: 1995-99 TAHOE/YUKON 4 DOOR
APLICACIÓN: TAHOE/YUKON DE 4 PUERTAS, MOD. 1995-1999
APPLICATION: TAHOE/YUKON 4 PORTES 1995-99
1
CONTENTS - CONTENIDO
(1) Y CONDUCTOR
PASSAGER (1) ET CONDUCTEUR (2)
PASSAGER (4) ET CONDUCTEUR (5)
2
- CONTENU
(2)
(4) Y CONDUCTOR (5)
NOTE:
Make sure the clearance holes in the rear bracket
NOTE:
On the driver side, adjust bottom rear hook so the
WO:
4
3 5
TOOLS - HERRAMIENTA
3/4" SOCKET
3/4" WRENCH
18MM SOCKET
15MM SOCKET
RATCHET
TORQUE WRENCH
DADO DE 3/4"
LLAVE DE TUERCAS DE 3/4"
DADO DE 18MM"
DADO DE 15MM"
MANERAL
LLAVE DE TORQUE
DOUILLE 3/4 PO
CLE 3/4 PO
DOUILLE 18MM
DOUILLE 15MM
CLIQUET
CLE DE COUPLE
75-0557 REVISION A 3/3/08
6
- OUTILS