Westin 25-0795 Instrucciones

AUTOMOTIVE PRODUCTS, INC.
STEP BAR ASSEMBLIES
ENSAMBLES DE ESTRIBOS
MONTAGES DE MARCHE-PIEDS
25-0795
25-0800
ITEM QTY
1,2 2 STEP BAR, PASSENGER (1) AND DRIVER (2)
3,4 2 FRONT BRACKET
5 2 REAR BRACKET
6 2 REAR MOUNT PLATE
7 4 1/2-13 X 1.75" HEX HEAD BOLT
8 4 1/2" LOCK WASHER
9 6 1/2" FLAT WASHER
10 6 3/8-16 X 1.25" HEX HEAD BOLT
11 8 3/8" FLAT WASHER
12 6 3/8" LOCK WASHER
13 6 3/8-16 HEX NUT
14 4 5/16-18 X 1.00" HEX HEAD BOLT
15 4 5/16" FLAT WASHER
16 4 5/16" LOCK WASHER
17 4 5/16-18 HEX NUT
1,2 2 ESTRIBOS, ACOMPAÑANTE
3,4 2 SOPORTES DELANTERAS, ACOMPAÑANTE
5 2 SOPORTES TRASERAS
6 2 PLACA DE MONTAJE TRASERAS
7 4 PERNOS CON CABEZA HEXAGONAL DE 1/2-13 X 1,75"
8 4 ARANDELAS DE PRESIÓN DE 1/2"
9 6 ARANDELAS PLANAS DE 1/2"
10 6 PERNOS CON CABEZA HEXAGONAL DE 3/8-16 X 1,25"
11 8 ARANDELAS PLANAS DE 3/8"
12 6 ARANDELAS DE PRESIÓN DE 3/8"
13 6 TUERCAS HEXAGONALES DE 3/8-16
14 4 PERNOS CON CABEZA HEXAGONAL DE 5/16-18 X 1,00"
15 4 ARANDELAS PLANAS DE 5/16"
16 4 ARANDELAS DE PRESIÓN DE 5/16"
17 4 TUERCAS HEXAGONALES DE 5/16-18
1,2 2 MARCHE-PIEDS, PASSAGER
3,4 2 SUPPORTS, PASSAGER
5 2 SUPPORTS ARRIÈRE
6 2 PLAQUETTE DE MONTAGE ARRIÈRE
7 4 BOULON À TÊTE HEXAGONALE 1/2-13 X 1,75 PO
8 4 RONDELLE À FREIN 1/2 PO
9 6 RONDELLE PLATE 1/2 PO
10 6 BOULON À TÊTE HEXAGONALE 3/8-16 X1,25 PO
11 8 RONDELLE PLATE 3/8 PO
12 6 RONDELLE À FREIN 3/8 PO
13 6 ÉCROUS HEXAGONAUX 3/8-16
14 4 BOULON A TÊTE HEXAGONALE 5/16-18 X 1,25 PO
15 4 RONDELLE PLATE 5/16 PO
16 4 RONDELLE À FREIN 5/16 PO
17 4 ÉCROUS HEXAGONAUX 5/16-18
STEP 1. Remove the contents from box and check for damage. Verify all parts are present. Read instructions completely before beginning.
STEP 2. Remove existing rear shackle nut from front leaf spring assembly as shown. Place a 1/2" flat washer over shackle bolt and install front
bracket over the shackle bolt and secure by replacing the existing shackle nut. Hand tighten. NOTE: Front bracket is positioned so
the bent flange is facing away from the frame and support flange with the 7/16" hole is facing towards the front of vehicle.
STEP 3. Once front bracket is in place, be sure support flange with the 7/16" hole is positioned against the front of the body mount as shown.
Using the hole in the support flange as a guide, drill a 7/16" hole in front face of the body mount.
STEP 4. Attach front bracket support flange to body mount using 3/8" fasteners and torque fasteners. Recommended torque values are 26
FT. Lbs. and 3/8" fasteners and 75 Ft. Lbs. for existing shackle nut.
STEP 5. Attach rear bracket to bottom flange of frame using 3/8" fasteners. Leave loose.
INSTRUCTIONS-INSTRUCCIONES-CONSIGNES
APPLICATION: 1980-98 FORD F-SERIES CREW CAB 4WD
APLICACIÓN: FORD SERIE F CON DOBLE CABINA 4WD, MOD. 1980-98
APPLICATION: FORD F-SERIES CABINE DOUBLE 1980-98
2
CONTENTS - CONTENIDO - CONTENU
, PASSENGER (3) AND DRIVER (4)
(1) Y CONDUCTOR
(1) ET CONDUCTEUR (2)
(3) ET CONDUCTEUR (4)
1
(2)
(3) Y CONDUCTOR (4)
WO:
4
5
3
TOOLS - HERRAMIENTA - OUTILS
3/4" SOCKET
3/4" WRENCH
9/16" SOCKET
9/16" WRENCH
1/2" SOCKET
1/2" WRENCH
7/16" DRILL BIT
21MM SOCKET
DRILL
RATCHET
TORQUE WRENCH
DADO DE 3/4"
LLAVE DE TUERCAS DE 3/4"
DADO DE 9/16"
LLAVE DE TUERCAS DE 9/16"
DADO DE 1/2"
LLAVE DE TUERCAS DE 1/2"
BROCA DE 7/16"
DADO DE 21MM
TALADRO
MANERAL
LLAVE DE TORQUE
DOUILLE 3/4 PO
Cl 3/4 PO É
DOUILLE 9/16 PO
CL 9/16 PO É
DOUILL1/2 PO
MÈCHE 7/16 PO
DOUILLE 21MM
PERCEUSE
CLIQUET
CL DE COUPLE É
75-0171 REVISION C 9/10/08
6