Invacare Revato H335 Manual Del Usuario página 6

Invacare® Revato
R7767 – Aesthetic Cover (Fig. 6)
Pos.
Designation
Plastic cover
B
Screw and nut
C
Protective cap
D
4 Setup and Usage
4.1 Installing Support Folding Handle
WARNING!
Risk of Falling!
– Mount only to walls that have a sufficient
load-bearing capacity.
Defining the Installation Height (Fig. 1)
1. With the user standing upright, without shoes, measure
the height of the thumb's upper joint. This height
corresponds to the support bar's highest point A (middle
of support bar).
Installing the Support Folding Handle (Fig. 1)
1. Insert the 2° adjustment plate D.
2. Mark out the location of the holes on the wall (2 above
and 2 below outside) taking into account the previously
measured height.
3. Remove the 2° adjustment plate.
4. Position the wall attachment socket C for the support
bar accordingly.
5. Drill and insert 4 dowels appropriate for the type of wall.
6. Fix the socket to the wall using suitable screws, washers.
7. Snap the guard B onto the socket.
8. Insert the 2° adjustment plate from below again.
Adjusting the Height
The support bar is supplied with a 2° adjustment
plate D. To adjust the height of the support bar, use
option R7768 (3 adjustment plates of 0°, 2° and 4°).
1. Remove the 2° adjustment plate.
2. To lower by 10 mm, insert the 0° adjustment plate E.
3. To raise by 10 mm, insert the 4° adjustment plate F.
Installing the Support Leg (Fig. 2)
1. Remove the socket's guard, if fitted.
2. Remove the end cap C, if fitted or the cover on the
lower tube of the support bar D.
3. If not fitted, install the hinge piece B by sliding it onto
the lower tube. If necessary, use a plastic mallet. Fix
with one screw and cover with two protective caps.
4. Install the front end of the guide J into the oblong hole
in the support leg I using a plastic mallet and starlock
retainer ring H.
5. Remove the lower left-hand fixing screw G from the
socket E.
6. Position the guide J on the outside of the support bar,
the end with the wall hinge F pointing towards the
support wall or socket E.
7. Fasten the wall hinge F using the socket's lower,
left-hand side fixing screw G.
8. Insert the upper end of the support leg I into the hinge
piece B. Fasten it using the screw and position two
protective caps K.
9. Install the socket's guard.
10. Check that the whole assembly is firm and operates
correctly.
6
Adjusting the Height (Fig. 2)
1. To decrease the height of the support leg turn the foot
Quantity
1
2. To increase the height of the support leg turn the foot
1
2
Installing the Floor Mounted Console (R7763) (Fig. 3)
1. Position the upright A.
2. The plate F resting on the floor must have its longest
3. Mark out the location of the 4 screws.
4. Drill and insert 4 dowels appropriate to the type of floor.
5. Fix the plate to the floor using suitable screws.
6. Position the plate B with the rounded section towards
7. Fasten the plate B and the support bar G with the two
8. With the user standing upright, without shoes, measure
9. Tighten the nuts D on the two clamps C.
10. Install the socket's guard.
11. Check that the whole assembly is firm.
4.2 Installing Options
The basic version can be fitted with the following options:
•
•
•
Installing the Toilet Paper Holder (Fig. 4)
1. If fitted, remove the end cap I from the lower support
2. Remove the protective cap C from the hinge piece B
3. Insert the toilet roll support A into the hinge piece B.
4. Position the spacer G and lock the assembly in place
5. Attach the hinge piece B by pressing or by tapping with
6. Check that the whole assembly is firm.
Installing the Armpad (R7766) (Fig. 5)
1. If fitted, remove the black end cap D from the support
2. Clean the parts to be glued together with acetone before
3. Apply the whole tube of glue to the inside face of the
4. Press it down for approximately 30 seconds.
assembly L counterclockwise into the support leg I.
assembly clockwise out of the support leg.
The height of the support bar can additionally be
adjusted with the 0°, 2° and 4° adjustment plates
(R7768) like described above.
This option, when sealed to the floor, enables a
support bar to be fastened in place when the wall is
unsuitable for this.
side under the support bar G.
the bottom and the support bar G.
clamps C, washers E and nuts D supplied but without
tightening them.
the height of the upper joint of the user's thumb and
move the support bar to this height.
A toilet paper holder mounted on the support bar (Fig.
4).
A soft, comfortable armpad (R7766) glued to the end of
the upper support bar (Fig. 5).
An aesthetic cover (R7767) designed to hide the lower
tube (Fig. 6).
bar J.
using a screwdriver
with the fastener H.
a plastic mallet to the lower support bar J and fasten
with screw D and nut E. Attach a protective cap F
on each side.
bar's upper tube C.
applying the glue B.
armpad A and position it onto the support bar C being
aligned lengthwise, ensure the armpad to point straight
upward.
Full adhesion is only obtained after approximately 24
hours. Invacare is not responsible for any damage
caused by improper fixing or inappropriate use.
1572997-E