Cleaning, Maintenance And Ordering Of Spare Parts; Carbon Brushes; Disposal And Recycling - NUTOOL MP900N Manual Del Usuario

GB
8 CLEANING, MAINTENANCE AND
ORDERING OF SPARE PARTS
Always pull out the mains power plug before starting any
cleaning work.
8.1 Cleaning
• Keep all safety devices, air vents and the motor housing
free of dirt and dust as far as possible.
Wipe the equipment with a clean cloth or blow it with
compressed air at low pressure.
• We recommend that you clean the device immediately
each time you have finished using it.
• Clean the equipment regularly with a moist cloth and some
soft soap. Do not use cleaning agents or solvents; these
could attack the plastic parts of the equipment.
Ensure that no water can seep into the device.

8.2 Carbon brushes

In case of excessive sparking, have the carbon brushes
checked only by a qualified electrician.
Important! The carbon brushes should not be rep laced by
anyone but a qualified electrician.
8.3. Changing the planing knives (Fig. 12-13)
Important!
Always pull the plug out of the power socket before
doing any work on the equipment.
To change the planing knives, use the supplied wrench (a).
The hand-held electric plane comes with two carbide
metal reversible knives. Reversible knives have two
cutting edges and can be reversed. The guide slot on the
reversible knives ensures the same height setting after a
change. Replace a worn, blunt or damaged knife.
Carbide metal reversible knives cannot be resharpened.
Undo the three hexagonal screws (c) using the wrench (a)
supplied and push the carbide metal reversible knife out of
the planing shaft using a piece of wood. (see Fig. 12).
Clean the knife seat before fitting. Install the knives in
reverse order. Check that the planing knife conforms with
both ends of the planing shaft. Always replace both knives
to ensure a uniform chip depth.
Important!
Before using the hand-held electric plane make sure
the knives are installed securely and in the right place.
Check the correct setting (Fig. 13)
(8) Front base plate (moving plane shoe)
(5) Rear base plate (fixed plane shoe)
1. Correct adjustment
Result: Smooth planed surfaces
2. Notches in the surface
Problem: The cutting edge on the planing knife (or both
planing knives) is not parallel to the height of the rear base
plate.
3. Furrows at the start of the planed surface
Problem: The cutting edge on the planing knife (or both
planing knives) is below the height of the rear base plate.
4. Furrows at the end of the planed surface
Problem: The cutting edge on the planing knife (or both
planing knives) is above the height of the rear base plate.
8.4 Replacing the drive belt (Fig. 14-15)
• The belt should be replaced by a trained expert.
• The drive belt (b) must be replaced if it is worn.
• Undo the screws (a) and remove belt cover at the sides (6).
• Remove the worn belt drive (b) and clean the two belt
pulleys (c/d).
• Place the new drive belt on the small belt pulley (c) and pull
the belt onto the large belt pulley (d) whilst turning the
planing shaft.
• Ensure that the longitudinal grooves on the drive belt are
in the guide grooves on the drive wheels.
• Fit the belt cover (6) and secure it with the screws (a).
8.5 Maintenance
There are no parts inside the equipment which require
additional maintenance.
8.6 Ordering replacement parts
Please quote the following data when ordering replacement
parts:
• Type of machine
• Article number of the machine
• Identification number of the machine
• Replacement part number of the part required

9 DISPOSAL AND RECYCLING

The unit is supplied in packaging to prevent its being damaged
in transit. This packaging is raw material and can therefore be
reused or can be returned to the raw material system.
The unit and its accessories are made of various types of
material, such as metal and plastic.
Defective components must be disposed of as special
waste. Ask your dealer or your local council.
16