Getting Started - Hoover POWER SCRUB XL Manual Del Usuario

GETTING STARTED

ASSEMBLY
Fully assemble product prior to use.
1
Insert the handle into the base.
2
Align the groove on the backside of the
clean water tank with the handle and drop
straight down.
OPERATION
CAUTION:
DO NOT USE THIS
EXTRACTOR ON HARD FLOORS. USING
THIS PRODUCT ON HARD FLOORS MAY
SCRATCH OR DAMAGE YOUR FLOOR.
CAUTION:
Use extra care when
cleaning on stairs. To avoid personal
injury or damage, and to prevent the
cleaner from falling, always place
cleaner at the bottom of stairs or on
floor. Do not place cleaner on stairs or
furniture, as it may result in injury or
damage.
WARNING:
To reduce the risk of
personal injury, unplug before
cleaning or servicing.
FILL THE CLEAN WATER TANK
1
Lift up to remove the Clean Water Tank,
then remove the cap and add warm
water to the fill line. Add 3oz. of Hoover
Solution. Secure cap.
CLEANING FLUID
SEE THE HOOVER'S SOLUTION GUIDE insert or
visit Hoover.com/cleaning-solutions.
2
Align the tank and firmly press it into
place.
NOTE: Test for colorfastness in a small,
hidden area. Gently rub surface with a
dampened white cloth. Wait ten minutes and
check for color removal or bleed with a white
paper towel.
NOTE: For the best results, vacuum carpet
and upholstery thoroughly with a HOOVER®
vacuum before use.
QUICK CLEAN MODE
NOTE: Feature included with select models
only.
1
To engage Quick Clean Mode, turn knob
counterclockwise until engaged.
2
Return to Deep Clean mode by turning
knob clockwise.
HOW TO USE
1
Plug the cord into an electrical outlet.
Recline
On/Off
2
Turn unit ON/OFF with side pedal.
3
Recline unit with the middle pedal.
4
Squeeze trigger to apply water and
cleaning solution.
5
Slowly push forward with trigger pressed
to wash, then slowly pull backwards with
trigger released to dry.
NOTE: For Best Results, rinse the carpet after
deep cleaning with clean water only. This will
remove residual carpet cleaning solution from
your carpets. To rinse with clean water only,
remove the solution tank from the unit and
then repeat steps 4 and 5.
EMPTY THE RECOVERY TANK
NOTE: To maintain proper suction, empty Tank
when Red Bobber is visible.
1
Turn the cleaner off and unplug from
electrical outlet.
2
Grab the Recovery Water Tank handle
and lift up and outward to remove it. A
second handle is provided on the back of
the Recovery tank for carrying the tank.
3
Unlatch the tank lid and empty it. Rinse
and allow to air dry.
USING THE HOSE
CAUTION:
Always turn off
appliance before connecting or
disconnecting hose.
CAUTION:
Not to be used for
grooming a pet.
1
Attach hose by opening the Hose Connec-
tion Port on the nozzle.
2
Hold open the Hose Solution Port door.
Plug the Hose Solution Tube connector
firmly into the Hose Solution Port.
3
To drain the hose, run the unit and do
not press the spray button on the hose/
tool end.
REMOVING THE HOSE
1
Press the button and firmly pull up to
remove the Hose Solution Tube from the
Solution Port.
2
The Hose port Door is spring loaded to
close automatically. Ensure the Hose
Port Door is fully shut for the best
performance.
NOTE: To ensure maximum performance and
to protect your carpet, be sure to place the
handle in the upright position while using
the hose.
HOW TO USE TOOLS
CAUTION:
To reduce the risk of
injury from moving parts - Unplug
before connecting SpinScrub® Hand
Tool. Not to be used for grooming pets.
1
Place the handle in the upright position.
This will shut off the SpinScrub® brushes.
2
Connect tool to hose by sliding it onto the
connector until it locks into place.
3
Using your thumb, push forward and up
on the latch to remove tool.
NOTE: The Antimicrobial pet tool included
with select models only has a button to
release the tool from the hose.
HOW TO USE TOOLS
(CONT'D)
4
Turn cleaner ON.
5
Pre-spray the carpeted stair by holding
the tool about one inch above the carpet
and push it forward while pressing the
trigger.
6
Position tool against the riser and slightly
press it into carpet pile. Press the trigger
and pull the tool slowly over the carpet.
Release trigger at end of stroke.
7
Lift tool, and position it against riser. Pull
tool slowly over carpet without pressing
trigger.
NOTE: Overlap strokes by 1/2 inch to help
prevent streaking.
MAINTENANCE
WARNING:
To reduce the risk of
personal injury, unplug before
cleaning or servicing.
IMPORTANT:
To prevent
possible leaking, remove Clean Water
Tank and Dirty Water Tank.
This product contains no serviceable parts.
If appliance is not working as it should, has been
dropped, damaged, left outdoors, or dropped into
water, call customer service at 1.800.944.9200
prior to continuing use.
LUBRICATION: The motor is equipped with
bearings which contain sufficient lubrication
for their lifetime. The addition of lubricant
could cause damage. Do not add lubricant to
motor bearings.
CORD STORAGE: Wrap the power cord around
the cord hooks for convenient storage. Attach
the plug end to the cord.
NOZZLE CARE
1
First turn off and unplug the carpet
cleaner. Remove Recovery Tank.
2
Pull up on the Nozzle slightly to unsnap,
then pull the Nozzle forward to remove it
from carpet cleaner. Rinse with water and
allow to air dry.
TROUBLESHOOTING
WARNING:
To reduce the risk
of personal injury, unplug before
cleaning or servicing.
THIS PRODUCT CONTAINS NO SERVICEABLE PARTS.
IF APPLIANCE IS NOT WORKING AS IT SHOULD, HAS BEEN DROPPED, DAMAGED, LEFT
OUTDOORS, OR DROPPED INTO WATER, CALL CUSTOMER SERVICE AT 1-800-944-9200 PRIOR
TO CONTINUING USE.
NOZZLE CARE
(CONT'D)
3
To replace it, position Nozzle onto the
front end while making sure to align the
tabs at the bottom of the Nozzle with the
notches on the foot.
4
Snap Nozzle to foot and rotate the latch
into the lock position.
IMPORTANT: The nozzle must be in the proper
position for the Dirty Water Tank to go on
properly and for the unit to have proper
suction.
BRUSH CARE
1
Remove the tanks and place the handle in
the upright position, tilt the cleaner back
until handle rests on the floor.
2
Push the latches out on the side of the
foot until they lock open.
3
The Brush assembly should be free to
pull out.
4
Rinse the brushes under running water.
5
Replace them by aligning the center drive
post and note the arrows indicating the
front of the machine. Push firmly until the
latches lock into place.
CAUTION:
To reduce the risk of
injury from moving parts - Unplug
before servicing. Do not use cleaner
without brushes in place.