Electrical Connections - Envirolite EVR6SLICAT Instrucciones De Instalación

CEILING JOIST INSTALLATION
1. Choose the location for the fixture, taking into consideration the
required 7" clearance and the accessibility to the electrical
supply.
2. Raise the housing/hanger bar assembly to the desired location
between the two ceiling joists. Adjust the width of both hanger
bars to the distance between the joists. Position the assembly so
that the mounting clips of the hanger bars cup underneath the
bottom edges of the joists. Hammer down the nails of the hanger
bars into the joists to secure the assembly into place.
(FIG. 3 & FIG. 4)
Joist
Nail
Mounting
Clip
Hammer
Hanger bar
3. Slide the plaster frame along the hanger bars to the desired
position. Using pliers squeeze the guides of the plaster frame
tightly around the hanger bars to lock the position of the plaster
frame.
4. Proceed to the "ELECTRICAL CONNECTIONS" section.
5. Install the insulation around the housing, if desired. Install the
ceiling material, such as drywall, over the housing. A template is
provided to assist in making the holes in the ceiling material.
(NOTE: Blown-in Insulation may also be installed after the ceiling
material has been installed.)
6. Proceed to the "TRIM INSTALLATION" section.
DROP CEILING INSTALLATION
1. Choose the location for the fixture, taking into consideration the
required 7" clearance and the accessibility to the electrical
supply.
2. Install a ceiling tile onto the T-bar grid at the installation location.
Using the provided template and a keyhole saw make a hole at
the desired location in the ceiling tile.
FIG. 3
Nail
Mounting
Bottom edge
Clip
of joist
Housing
Plaster
Frame
Joist
FIG. 4
ALL RIGHTS RESERVED. COPYRIGHT  Envirolite 2016
3. Place the housing/hanger bar assembly onto the ceiling tile into
the newly created hole. Adjust the width of both hanger bars to
the distance between the two T-bars, aligning each mounting
clip with the top of its corresponding T-bar. Press down on all
mounting clips until they snap onto the T-bar. (FIG. 5 and FIG.
6) NOTE: Holes are provided on the mounting clips that can
be used to secure the hanger bars to the T-bar. Parts (I.e.
screws, hex nuts) can be purchased separately for this purpose.
Proceed to the "ELECTRICAL
4.
CONNECTIONS" section.
Proceed to the "TRIM
5.
INSTALLATION" section.
FIG. 5
T-bar

ELECTRICAL CONNECTIONS

WARNING: First disconnect electricity at the circuit breaker or
the fuse box. Disconnecting power by using the wall switch is
not sufficient to prevent electrical shock.
1. Using BX (armored) or NM (Romex) cable, run the supply wiring
from the power supply source to the fixture location.
WARNING - Use supply wires rated 90°C or higher.
2. Open the hinged junction box's door by lifting the metal latch.
A. FOR BX (ARMORED) CABLE - Break off one of the round
knockouts (FIG. 8) using a screwdriver. Secure an appropriately
sized BX cable connector to the knockout opening. Feed the BX
cable through the connector, providing 6" of slack inside the
junction box. Tighten the connector to secure the cable in place.
B. FOR NM (ROMEX) CABLE – Break off one of the rectangular
knockouts located on the top of the junction box using a
screwdriver, creating a slot. (FIG. 7) Slide the NM cable into the
slot, as shown, making sure there is 6" of slack inside the
junction box. (FIG. 8)
3. Remove at least 3" of the cable's outer sheath and remove the
plastic or paper over-wrap. Strip approximately 3/8" of insulation
from the ends of all supply wires. Using the provided "quick-
connect" wire connectors, make the following wire connections
within the junction box:
WHITE Fixture Wire to WHITE (NEUTRAL) Supply Wire
BLACK Fixture Wire to BLACK (HOT) Supply Wire
GREEN Fixture Wire to GREEN/BARE (GROUND) Supply Wire
T-bar
Mounting
Hanger
Bar
FIG. 6
Mounting
Clip
T-bar
Mounting
Clip
Clip