BLACK&DECKER Dustbuster Flexi PD1200 Manual Del Usuario página 5

Features
This appliance includes some or all of the following features.
1. On/off power switch
2. Removable hose/handle
3. Locking ring
4. Hose
5. Filter cleaning wheel
6. Charging inlet
7. Transparent door
8. LED charging indicator
9. Door latch
10. 2-in-1 combi nozzle accessory
11. Accessory clip
The following accessories are only available with model
number PD1200 (fig. A & B):
12. Accessory caddy
13. Powered brush head
14. Crevice tool
The powered brush head is not included with all models.
Assembly
Mounting accessories (fig. A, B & C)
The 2-in-1 combi nozzle (10) has a brush that can be folded
forward for dusting and upholstery cleaning.
The crevice tool (14) allows for vacuuming in narrow and
hard to-reach places.
The powered brush head (13) has its own rechargeable
batteries and is charged separately from the appliance, refer
to "Charging the battery" section.
To fit an accessory press the accessory clip (11) and
slide the accessory onto the handle (2).
To remove an accessory, press the accessory clip (11)
and remove the accessory.
The handle (2) can be removed from the hose (4) allowing
the accessories to be connected directly to the hose cuff (18)
when required. To remove the handle:
Unclip the handle (2) from the appliance.
Rotate the locking ring (3) anti-clockwise to release the
clips.
Pull the hose (4) away from the handle (2).
Fit the accessory directly to the hose cuff (18).
To refit the handle:
Remove the accessory from the hose.
Push the hose (4) into the handle (2). Rotate the locking
ring (3) clockwise until it clicks into place.
Fitting the accessory caddy (PD1200) (fig. D)
When not in use, accessories can be stored in the accessory
caddy (12). The accessory caddy can be removed if
necessary.
To install the accessory caddy (12) slide it onto the lugs
on the body of the appliance until it clicks into place.
To remove the accessory caddy (12) pull it away from
the base of the appliance.
Use
Before first use, the batteries must be charged for at least
16 hours.
Connect the appliance and the powered brush head
(13) to the charger for a minimum of 16 hours.
Charge the batteries as described below.
You may need to charge/discharge the appliance a minimum
of 5 times in order to achieve the best running time
performance.
Charging the battery (fig. A & E)
Warning! Do not charge the battery at ambient
temperatures below 10°C or above 40°C.
Note: If your vacuum cleaner is supplied with a single
charger with a dual lead to charge both the appliance and the
powered brush head (13), the jack plugs are the same size
and are interchangeable. The appliance and the powered
brush head (13) can be charged at the same time.
To charge the appliance:
Make sure that the appliance is switched off. The
battery will not be charged with the on/off power switch
(1) in the on position.
Insert the plug into the charging inlet (6) in the base.
Plug in the charger and switch on at the mains.
The charging indicator (8) will be lit.
For the first charging, leave the appliance to charge for
at least 16 hours.
To charge the powered brush head:
Make sure that the powered brush head (13) is switched
off. The battery will not be charged with the on/off power
switch (17) in the on position.
Insert the plug into the charger inlet (16).
Plug in the charger and switch on at the mains.
The charging indicator (15) will be lit.
For the first charging, leave the appliance to charge for
at least 16 hours.
While charging, the charger may become warm. This is
normal and does not indicate a problem.
ENGLISH
5