OttLite 19047C Guia De Inicio Rapido

C
B
A
LED Clip and Freestanding Dual Magnifier
19047C 190TUC 19021C 15900C
GX8028
D
H
J
L
F
E
M
B
ENGLISH
CONGRATULATIONS!
You've purchased the finest in natural lighting technology
with your new OttLite product.
PRODUCT REGISTRATION FORM
Please complete the enclosed Product Registration Form and
return it today by mail, or register online by going to:
http:/www.OttLite.com//warranty
DESk LAMP ASSEMbLy
Remove the lamp and all parts from packing and verify
1.
presence of all lamp parts before proceeding.
Base part (A) qty. 1
Large part (D) qty. 1
Small part (E) qty. 1
Body part (B) qty. 1
Battery Door part (M) qty. 1
The LED Magnifier is powered by 3 AAA batteries
2.
(not included), alkaline or rechargeable batteries are
recommended.
3. Install batteries per bATTERy INSTALLATION procedure.
Install the selected magnifier by aligning the slot in the
4.
magnifier base (L) with the tab in the socket (J); ensure
that the magnifier plug fits into the socket hole.
5. Push the magnifier (D or E) fully into the socket (J) then
gently twist counterclockwise approximately 40 degrees to
lock it in place.
To remove an installed magnifier (D or E), gently rotate
6.
the magnifier clockwise in the socket (J) approximately 45
degrees then pull it from the socket.
The unused magnifier should be stored in cup (k); simply
7.
insert the magnifier plug into the hole of the cup.
8. Your OttLite LED Magnifier light can be used as a table
lamp or clipped to an appropriate edge of ¼ to 1 inch
thickness.
Follow the selected method of mounting as detailed below.
TAbLE MOUNT
Set lamp base (A) on a steady flat surface.
1.
Open the clip (F) and place lamp body (b) fully into the
2.
holder cavity in the base (A).
Release the clip (F) verifying that the lamp body is held
3.
firmly to the base (A).
Position the magnifier as needed by grasping socket (J)
4.
and flexing the stem (C) while holding the base steady.
Turn the LED light on or off by depressing switch (H).
5.
DO NOT FORCE the flexible stem into any position as lamp
damage may result.
CLIP MOUNT
1. If attached to base, squeeze the clip (F) to release the
lamp from the base (A).
2. An appropriate attachment edge will be thicker than
¼ inch and less than 1 inch.
3. Attach the clip only if the entire clip can be utilized to hold
the lamp.
4. Position the magnifier as needed by grasping socket (J)
and flexing the stem (C) while holding the lamp body (b)
steady.
Turn the LED light on or off by depressing switch (H).
5.
DO NOT FORCE the flexible stem into any position as lamp
damage may result.
bATTERy INSTALLATION
1. Your OttLite LED Magnifier light is powered by 3 AAA
batteries (not provided). With standard alkaline batteries,
your LED Magnifier light will operate approximately 10
hours. Light output will slowly diminish as the batteries
lose energy.
Warning: keep away from children. If swallowed,
promptly see doctor. Do not install backwards, charge,
put in fire or mix with other battery types – may
explode or leak causing injury.
2. To install batteries in your LED Magnifier light, push
battery door (M) toward the stem (C) while slightly
depressing the door near the tab (see diagram).
Install the 3 batteries as indicated by the graphic inside the
3.
battery compartment. Battery negative terminals should
point toward the spring.
4. Replace the battery door by laying it on the lamp body (b)
then slide it away from the stem to engage the tab to the
lamp body; a click should be heard as it locks into place.
Notice: Only replace batteries as a simultaneous
set and do not mix with older batteries. Remove
batteries if consumed or if the light has not been in
use for a long period of time.
CAUTION: Risk of fire! Never place the Magnifier
Attachment under direct sunlight.
Enjoy your OttLite LED Clip and Freestanding Magnifier
REV032614
!