Publicidad
Idiomas disponibles
Idiomas disponibles
English
INSTALLATION INSTRUCTIONS
Water Supply
Recommended
Maximum
Hot Water Temperature
65 C° (~150F)
80 C° (~175F)
Working Pressure
3 BAR (~45PSI)
5 BAR (~75PSI)
In case of pressures over 5 BAR (~75 PSI), we
screw (3.D). Excessive tightening can affect the
recommend to use a pressure reducer.
correct function of the system or damage it. The
Before proceeding with the assembly, purge the
thermostatic cartridge is equipped with a safety
hot and cold water pipes so as to avoid the
anti-scalding retainer set at 100°F (38°C). For
accumulation of dirt and impurities that could
higher temperatures push the button on the
affect the function of the faucet.
adjustment handle. In case of hot or cold water
pressure failure, the flow will automatically stop.
FIG. 01
With a screwdriver loosen the stop cocks (3.H)
Remove with a screwdriver the protection covers
in anti-clockwise direction.
(1.A). Use the plug (1.B) if necessary.
FIG. 04
FIG. 02
Remove the protection tape of the adhesive
Fit the faucet body to the wall with the shower
sponge (4.D) and apply it on the back of the
outlet pointing upwards, connect the hot water
plate (4.C).
supply to the left inlet and the cold water supply
Fit the flat washers (4.B) and (4.A) on the plate
to the right one.
(4.C) and install it on the thermostatic body till it
The depth of the wall niche must correspond
is flush to the wall.
(wall coating included) to the tolerance given
by the MIN/MAX references given on the
FIG. 05
plastic cover (2.A).
Control handles installation.
Once all connections have been carried out,
For the upper portion with the stop cock, follow
activate the faucet at the working pressure
the instructions given below:
(we recommend maintaining the water flow
Assemble the protection cover (5.M) on the
for a few minutes so as to purge the system
screw down and fit the spacer (5.L) on the
from any debris and/or dirt inside the piping).
screw down bar.
Temporarily remove the protection cover (2.A)
Position the handle (5.I) and tighten it with
to check if there are leakages and if the system
the screw (5.H). Complete the operation by
works regularly, reinstall the protection cover
inserting the cap (5.G).
(2.A) and finish the external wall surface.
For the lower portion with the thermostatic
cartridge, follow the instructions given below:
FIG. 03
install the handle (5.E) placing the spacer (5.F)
Remove the protection cover (2.A) as shown
on the thermostatic cartridge without moving
in FIG. 02. With a screwdriver turn the stop
the bar so as to not compromise the cartridge
cocks (3.H) clockwise, loosen the fitting screw
calibration. Fit the knob (5.D) and fasten it with
(3.D) using the proper wrench and pull out the
the screw (5.B) inserting the flat washer (5.C)
test plug (3.E). Insert the o-ring (3.C) and the
and place the finishing cap (5.A).
sleeve (3.B) on the thermostatic body. Fit the
o-ring (3.G) into the housing on the faucet body
FIG. 06
and assemble the protection cylinder (3.F). Use
To replace only the lever (6.L) follow the
a small quantity of the special grease included
instructions given below:
to lightly lubricate the o-rings of the thermostatic
Remove the cap (6.H), loosen the screw (6.I)
cartridge (3.A). Insert the cartridge in the faucet
and pull out the lever (6.L).
housing carefully aligning the positioning hole
Install the new lever (6.L) and fasten it using the
with the housing of the fitting screw (3.D), then
screw (6.I), complete by inserting the cap (6.H).
tighten the latter. Warning!, Do not force the
Istruz. art. 8869000.indd 4-6
FIG. 01
Minimum
15 C° (~60F)
0.5 BAR (~7PSI)
FIG. 03
FIG. 05
FIG. 02
FIG. 06
FIG. 04
FIG. 07
FIG. 08
26/04/11 09:57
Publicidad
