YATO YT-82140 Manual Original página 15

GB
protective clothes and shoes. It is also required to use dust masks to protect the respiratory system.
Only well sharpened knives ensure correct planing and prolong the durability of the tool.
Do not overload the plane to the point when it stops.
Do not ever proceed to plane surfaces with metal elements (nails, screws, stitches etc.).
Use only verified knives which are approved for the rotational speed indicated on the tool.
The plug of the tool may be inserted into the mains socket only if the device is off.
The power supply cord must be always placed behind the device.
The plane must be applied to the processed object only after it has been started.
During planing the plane must adhere completely with the whole surface of the runner to the processed object.
During work the plane must be always guided with both hands.
Uniform moving of the plane during planing extends the life of the knives and reduces the risk of accidents.
Do not ever put your fingers into the shavings eject opening. If the opening is blocked, remove the plug from the mains contact
and clean the hole of the accumulated shavings, using a wooden stick.
Always connect an external dust extraction device.
Make regular breaks during work.
Do not overload the tool – the temperature of the external surfaces must not exceed 60°C.
Do not operate the plane as a stationary device.
Always observe general instructions of safe operation of electric tools.
Once the work with the plane has concluded, you may put it down when it has been disconnected from the mains socket and the
knife shaft has completely stopped.
Once the work has finished perform maintenance activities and inspect the tool.
Planing of surfaces (XIV)
Hold the plane with both hands. Place one hand on the handle and the other one on the depth adjustments knob of the plane.
Adapt a secure and stable position. Apply the plane with the front section of the runner to the surface of the object to be processed,
making sure the knives do not touch the surface to be processed in any place. Turn the plane on with the switch and wait until the
knives have reached the nominal rotational speed, and only then move the plane forwards carefully.
At the initial stage of planing exert pressure on the front section of the plane, and at the end on its rear section.
For the purpose of initial planing you may increase the depth of planing, while in order to ensure the optimum quality of the surface
it is necessary to reduce the depth of planing and move the plane slower.
At the back edge of the base the plane has a support, which goes down once the rear section of the base is lifted, and once the
plane is put down again it prevents any contact of the knives with the material being processed (XV).
Before the operation of the tool is restarted, the support must be lifted during normal start of operation. During normal start of the
work the support is automatically lifted while the plane is driven along the processed material.
Attention! It is prohibited leave the plane with rotating knives on the support.
Planing of edges (XVI)
The foot of the plane has grooves of distinct depth, which makes it easier to bevel the edge of the material being processed. Set
the depth of planing with the knob. Place the foot of the plane so that the groove is aligned with the edge of the material being
processed. Start work as in case of planing of surfaces.
Attention! Depending on the depth of the groove, the whole range of the depth of planing may not be available. Only the central
groove permits using the whole range of the depth of planing.
Additional remarks
Once the task has been concluded, turn the jig saw off, remove the plug of the tool from the mains socket and inspect the ma-
chine.
The declared total value of vibration has been determined by means of a standard measurement method and may be used to
compare the tool with another one. The declared total value of vibration may be used for an initial evaluation of exposure.
Attention! The vibration caused during work with the tool may differ from the declared value, depending on the way in which the
tool is used.
Attention! It is required to determine safety measures to protect the operator, based on evaluation of exposure under actual
circumstances of operation of the machine (including all the phases of the working cycle, for example the time when the tool is off
or is idling, and the activation time).
MAINTENANCE AND OVERHAUL
ATTENTION! Before any adjustment, technical service or maintenance operations unplug the tool. Once the operations have been
finished, the technical conditions of the tool must be assessed by means of external evaluation and inspection of the following
elements: body and handle, conductor with a plug and deflection, functioning of the electric switch, patency of ventilation slots,
sparking of brushes, noise level of functioning of bearings and gears, start-up and smoothness of operation. During the guarantee
period, the user cannot dismantle the electric tools or change any sub-assemblies or elements, since it will cancel any guarantee
O R I G I N A L I N S T R U C T I O N S
15