Publicidad
Idiomas disponibles
Idiomas disponibles
• Contracting heat shrink pipes, soldering connectors
and clamps of sealing and electrical components�
• Changing the shape of acryl, PVC, polystyrene
products, pipes, plates, profiles and wet timber.
• Repairing surfboards, skis and other sports equip-
ment, repairing bumpers and other plastic automobile
parts�
• Waxing skis, furniture, and antiseptic timber treat-
ment�
• Loosening rusted or tight metal screws, nuts, bolts,
shrink-fitting, heat shrink treatment.
• Welding thermoplastic polymers, PVC and linoleum
flooring materials, PVC coated fabrics, tarpaulin and
foil�
• Soldering, tinplating and loosening of soldered
joints�
• Removing lacquer and paint coatings�
• Drying lacquer and paint coatings, adhesive and
spackling compounds�
• Acceleration of adhesion processes, activation of
adhesives�
• Thawing ladders, stairs, door locks, boot covers, car
doors, water pipes as well as defrosting fridges and
freezers�
• Mold and fungus control, disinfection of animal
housing�
• Lighting charcoal�
Using special nozzles
• Flat nozzle 9 is designed for treating large-area sur-
faces�
• Deflector nozzle 10 is used for treating one surface
and protecting the other (the heating of which is unde-
sirable, e�g� window glass)�
• Reflector nozzle 11 is used for changing the air flow
direction�
• Point nozzle 12 is for treating small-area surfaces as
well as for soldering�
General recommendations
• If necessary, put an appropriate special nozzle on
gun nozzle 1�
• Prepare accessories required for work performance
(scraper, palette knife, brush, etc�)�
• Switch on the power tool, adjust the air flow and
temperature as described above�
• After the operation completion, place on / off switch 5
in position "1" and let the power tool run for a while so
that it cools down, and only after that you can switch it
off (only for HLP20-600 K model)�
Special recommendations for performing different
types of work (see fig. 4-6)
Paint and coatings removal (see fig. 4.1) - install flat
nozzle 9, heat the surface area until the coating soft-
ens, and remove it with a palette knife or scraper 8�
Lacquer and paint coatings removal from window
frames (see fig. 4.2) - install deflector nozzle 10 cor-
rectly (to protect the glass), heat the surface area until
the coating softens, and remove it with a palette knife
or scraper 8�
The manufacturer reserves the possibility to introduce changes.
Forming plastic pipes (see fig. 5.1) - install reflector
nozzle 11� Fill the plastic pipe with sand and close it at
both ends to prevent pipe collapse� While moving the
pipe in the hot air flow, heat it and mould it as required.
Thawing water pipes (see fig. 5.2) - install reflector
nozzle 11� While moving the power tool, heat a frozen
area from the edge to the middle� While heating plastic
pipes, be careful not to overheat them�
Soldering (see fig. 6) - install point nozzle 12� Apply
solder paste on the soldering area� Depending on the
material, heat the soldering area for 50-120 seconds,
and then apply solder alloy� The solder alloy must melt
under the workpiece temperature�
Power tool maintenance /
preventive measures
Before carrying out any works on the power tool it
must be disconnected from the mains.
Taking care of accessories
Keep special nozzles and scraper 8 clean - remove all
materials stuck to them� Regularly sharpen the blade
of scraper 8 - this will facilitate the work and improve
its results�
Cleaning of the power tool
An indispensable condition for a safe long-term exploi-
tation of the power tool is to keep it clean� Regularly
flush the power tool with compressed air thought the
ventilation slots 4�
After-sales service and application service
Our after-sales service responds to your questions
concerning maintenance and repair of your product as
well as spare parts� Information about service centers,
parts diagrams and information about spare parts can
also be found under: www.dwt-pt.com�
•
Categorically not to drop any mechanical impact on
the packaging during transport�
• When unloading / loading is not allowed to use any
kind of technology that works on the principle of clamp-
ing packaging�
Recycle
disposing as waste.
Power tool, accessories and packaging should
be sorted for environment-friendly recycling�
The plastic components are labelled for categorized
recycling�
These instructions are printed on recycled paper man-
ufactured without chlorine�
English
10
Transportation
of the power tools
Environmental
protection
raw
materials
instead
of
Publicidad
