Publicidad
1
1
2
3
4
5
INSTRUCTION
UK
These operating instructions should be
read and followed up carefully before utilizing the
SUP board. Take special care to follow up the correct
sequence of inflating/deflating of the assembling
procedure.
CONTENTS
1 Inflatable Stand-Up paddleboard
1 Backpack
1 Aluminium adjustable paddle
1 Hand Pump
1 Leash.
1 Detachable skeg
1 Repair kit
1
1. H3 Valve
2. Front bungee cord
3. Non slip EVA pad
4. Carry handle
5. Metal ring
6. Fixed skeg
7. Detachable skeg
WARNING
- SUP can be very dangerous and physically
demanding. The user of this product should
understand that participating in stand up paddling
may involve serious injury or death.
- Seek SUP instruction from a licensed or certified
instructor.
- Always check weather forecasts prior to using
the SUP board. Never use the SUP board in
thunderstorms and lighting conditions.
2 | Instructions for use – Stand-up paddleboard
2
3
6
7
- Always use appropriate protective gear and wear
a personal flotation device. Wear the correct
protective clothing for the conditions such
as a wetsuit or a UV top. Cold water and cold
weather can result in hypothermia. Always carry
identification.
- Wear a helmet when appropriate.
- Do not exceed the maximum weight capacity of
150 kg.
- Do not operate the SUP board under the influence
of drugs and/or alcohol.
- This model is designed to be used in flat waters
(lake, rivers, sea shore) in standing and seating
position. It is not recommended to use the SUP
board in high waves nor for surfing.
- Beware of offshore winds and currents as they can
take you out to sea.
- Check your equipment prior to each use for signs of
wear, leaks or failure.
- Tie the included leash to your SUP board at all times.
- Children should always be under adult supervision.
- Always inform someone your paddling route, the
time and place of departure and your intended
time and place of arrival. Paddling alone is not
recommended.
- Watch out for other beach users especially
swimmers and children. Make sure you keep the
SUP board and paddle under control at all times.
- Never leave your SUP board for an extended period
of time on a warm surface like a beach or other
surfaces. This can cause damage to your board.
PREPARATIONS FOR INFLATING THE SUP
BOARD
Remove all sharp edged and pointed objects from the
surface in order to avoid damaging the SUP board.
1
4
1
2
2
3
3
ASSEMBLY INSTRUCTIONS / INFLATION / DEFLATION
Inflate the SUP board with the included hand pump.
2
1. Valve cap
2. Button
3. Valve base
- Unscrew the valve cap
and turn approximately 90 degrees so it is in the
"OUT" position.
- Insert the pump hose end piece and inflate it until
you will reach the required pressure. After inflation
tighten all the valve cap (clockwise). Only the valve
cap can ensure final AIR TIGHTNESS.
- To release air from the SUP board, remove the
valve cap
and push the button
1
approximately 90 degrees so it is in the "IN" position.
The correct pressure for this SUP board is
maximum 1 bar / 15 PSI (=1000 mBar)
DO NOT EXCEED THIS !!
Using an electrical pump or air compressor is at your
own risk. This can lead to damaging the SUP board.
DETACHABLE SKEG ON BACKSIDE OF SUP BOARD
It is recommended to use the detachable skeg in deep
water, where it will allow you to move forward in a
straight line. Do not use it in shallow water because
then the skeg can hit the bottom. The Skeg can be
placed on the SUP board if this is inflated or deflated.
To assemble the skeg push the skeg in the black part
on the back side of the SUP board. To lock the skeg
push the lock pin in the skeg base hole.
. Push the button
in
1
2
in and turn
2
Publicidad
