Set-Up The Unit; Electrical Installation - Oase Jumping Jet Rainbow Star Instrucciones De Uso

Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

Pos: 141 /Alle Produkte/Überschriften/H2 Gerät aufstellen @ 12\mod_1254925340890_121.doc @ 76901 @
4.2

Set-up the unit

Attention! Dangerous electrical voltage.
Possible consequences: Death or severe injury.
Protective measures:
Prior to reaching into the water, switch off the mains voltage to all units used in the water.
Switch off the mains voltage prior to carrying out work on the unit.
Pos: 142 /Alle Produkte/Dummy_module/Abstand 3pt @ 11\mod_1251901846864_0.doc @ 72826 @
Pos: 143 /Alle Produkte/Warnhinweise/E-ACHTUNG - Netzspannung abschalten @ 13\mod_1259760934607_121.doc @ 84730 @
Pos: 144 /Alle Produkte/Dummy_module/Abstand 3pt @ 11\mod_1251901846864_0.doc @ 72826 @
Pos: 145 /Alle Produkte/Sicherheit/ACHTUNG - Empfindliches Gerät# @ 13\mod_1256131358173_121.doc @ 80144 @
Attention! The unit is sensitive.
Possible consequences: Mechanical or electronic parts could be damaged.
Protective measures: Avoid hard impacts and vibrations of the unit.
Pos: 146 /Alle Produkte/Dummy_module/Abstand 3pt @ 11\mod_1251901846864_0.doc @ 72826 @
Pos: 147 /Pumpen/Schlammsauger/Jumping Jet Rainbow Star FT/INS Jumping Jet Rainbow Star FT montieren @ 13\mod_1256131953942_121.doc @ 80199 @
Install the Jumping Jet Rainbow Star level and free from vibrations on a sturdy platform.
1. Fasten the unit foot (23) on the platform using 3 screws (22) (not included in our scope of delivery).
Turn the unit to the desired position and tighten the screws (22) (Fig. C).
2. Connect the hose (2) (Fig. D)
In the case of steep inclination angles of the Jumping Jet Rainbow Star (1), the stepped hose
adapter (15) with socket (16) can be directly screwed onto the inlet (24).
In the case of flat inclination angles, screw the two angle pieces (17) on the inlet (24) to be able to fit
the stepped hose adapter (15) including the socket (16).
3. Slide the hose clip (14) over the hose (2), plug the hose (2) on the stepped hose adapter (15), and
secure by means of the hose clip (14).
4. Connect the other hose end to the pump. Adhere to the information given in the pump operating
instructions.
Pos: 148 /Alle Produkte/Dummy_module/Abstand 18 pt @ 6\mod_1196355593257_0.doc @ 41089 @
Pos: 149 /Alle Produkte/Überschriften/H1 Elektrische Installation @ 8\mod_1219935543509_121.doc @ 51295 @
5.

Electrical installation

Pos: 150 /Pumpen/Schlammsauger/Jumping Jet Rainbow Star FT/Anschluss der Stromversorgung Jumping Jet FT @ 13\mod_1255705447537_121.doc @ 79194 @
The unit foot is fitted with a 12 V connection box (12 V AC) as well as a DMX connection box (DMX)
(Fig. E).
Connection of the power supply
This is how to connect the cable to the 12 V power supply (Fig. E, F):
1. Remove both screws from the 12 V connection box(12 V AC) and remove the cover cap.
2. Insert the connection plug into the socket and secure with both screws (note the correct seating of
the seal in the plug).
DMX cable connection
This is how to connect the unit to the DMX control system (DMX control unit) a (Fig. E, F):
1. Remove the two screws from the DMX connection box (DMX) and remove the cover cap.
2. Insert the plug of the DMX cable of the DMX control unit in the socket for the DMX input signal
(DMX-IN) and secure by means of the two screws.
How to connect additional (max. 31) units to the DMX control system (Fig. G):
1. Remove the two screws and take off the cover cap.
2. Insert the plug of the DMX cable in the socket of the already connected unit for the DMX output
signal (DMX-OUT) and secure by means of the two screws. Insert the other plug of this DMX cable
in the socket for the DMX input signal (DMX-IN) of the next unit.
Pos: 151 /Alle Produkte/Dummy_module/===== Seitenwechsel ===== @ 0\mod_1125648978015_0.doc @ 1631 @
- GB -
19

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Dmx/01

Tabla de contenido