Genius INTERMODO4 Manual De Instrucciones página 6

3. MEMORY STORAGE OF RADIO CONTROLS
A maximum of 250 codes for channels 1-2 and 250
codes for channels 3-4 can be memory stored.
1. On the master radio control, simultaneously press and
hold down push-buttons P1 and P2.
2. The radio control LED begins to flash (for about 10
secs.).
3. Release both push-buttons.
Press, for 1 second, the push-button on the receiver
4.
(Fig.1 ref. ) relating to the channel you wish to
associate with the radio control.
5. The relevant LED on the receiver (Fig. 1 ref.
to flash slowly for 5 secs.
6. Within these 5 secs., while the radio control LED is still
flashing, press and hold down the required push-but-
ton on the radio control (the radio control LED lights
up on steady beam).
7. The LED on the board (Fig.1 ref.
beam for 1 second and then goes OFF, indicating that
storage was executed.
8. Release the radio control push-button.
Quickly press twice in succession the memory stored
9.
radio control push-button.
The board will send a command to the output
associated with the channel.
To add other radio controls, transfer the code of the
10.
memory-stored push-button of the radio control to
the relevant push-button of the radio controls to be
added, observing the following procedure:
a– On the memory stored radio control, simultaneously
press and hold down push-buttons P1 and P2.
b– The radio control LED begins to flash.
c– Release both push-buttons.
d– Press the memory stored push-button and hold it
down (the radio control LED lights up on steady
beam).
e– Bring the radio controls near, press and hold down
the push-button of the radio control to be ad-
You can command the receiver channels from different radio controls. (E.g.: radio control 1 commands channel
1, radio control 2 commands channel 2, etc..)
CHANNEL 1 CHANNEL 1
OUTPUT 1 OUTPUT 1 PULSE PULSE
OUTPUT 2 OUTPUT 2 / /
OUTPUT 3 OUTPUT 3 / /
OUTPUT 4 OUTPUT 4 / /
f–
ASSOCIATED WITH CHANNELS 1-2 OR 3-4
) begins
1.
) lights up on steady
2.
3.
4.
5. FUNCTION LOGIC
PULSE FROM RADIO CONTROL PULSE FROM RADIO CONTROL
CHANNEL 2 CHANNEL 2 CHANNEL 2 CHANNEL 2
dip switch 1=OFF dip switch 1=OFF dip switch 1=ON dip switch 1=ON
/ /
CONTACT CLOSED CONTACT CLOSED
UNTIL NEXT PULSE UNTIL NEXT PULSE
PULSE PULSE
FROM REMOTE FROM REMOTE
CONTROL CONTROL
/ /
/ /
6
ded, releasing it only after the double flash of
the radio control LED, which indicates learning
was executed.
Quickly press twice the push-button of the new
memory stored radio control.
The board will send a command to the output
associated with the channel.
4. DELETION OF ALL RADIO CONTROLS
This operation is NOT reversible and, if the radio con-
trols associated with channels 3-4 are deleted,
it also entails the deletion of activation timer of
output 4.
To delete ALL the radio control codes associated
with channels 1-2 or 3-4, hold down the rele-
vant push-button (Fig.1 ref.
(e.g. TO DELETE ALL RADIO CONTROLS ASSOCIATED
WITH CHANNELS 1-2, PRESS SW1 OR SW2).
The LED (Fig.1 ref. ) relating to the pressed push-
button flashes for the first 5 secs., and then flashes
more quickly for the next 5 secs.
The LED lights up on steady beam for 2 secs. and
then goes OFF.
Release the pressed push-button when the relevant
LED lights up on a steady beam.
CHANNEL 3 CHANNEL 3
/ / / /
/ /
/ / PULSE PULSE
/ / / /
) for 10 seconds.
CHANNEL 4 CHANNEL 4
/ /
/ /
/ /
CONTACT CLOSED CONTACT CLOSED
UNTIL END OF PRO- UNTIL END OF PRO-
GRAMMED TIME GRAMMED TIME