Care And Maintenance - AeroBed Classic Range Manual De Instrucciones

-- INFLATION
AeroBed
®
1 Remove your from its lightweight duffel bag. Keep bag for storage.
Note:
Product must be at room temperature prior to inflating.
Place your rolled up bed on the floor or other surface free of obstructions or
sharp objects.
2. Make certain the Quick Air Release Valve located at the foot of the bed is closed.
Bed should be stored with valve in the closed and latched position.
If the Air Release Valve is open, close it by using 2 thumbs to push cover and
snap into valve. Be careful to avoid pushing valve cover to the right or left as it
snaps into the valve opening.
This is the closed position. Open Air Release Valve.
3. Remove AC plug, cord sets and Comfort Remote Control from plastic bag and
AeroBed
®
shrink wrap. Your may have been supplied with two cord sets for
maximum convenience throughout the whole of Continental Europe and the UK.
Select the cord set that is appropriate for your electric supply outlets and connect
it to the pump. Ensure the plug of the cord set is fully inserted into the socket on
the end of the pump cord.
4. Because this is an electric device, ensure your hands are dry when connecting
the cord set to the pump or plugging it into the wall outlet, and do not use your
AeroBed
®
in or around water.
5. Plug into any standard polarized 220-240 volt AC electrical outlet.
(Note: this product is rated at 230V ~ 50Hz, 0.5A. 110-volt product sold outside
Europe).
Never use with an extension cord unless the plug can
be fully inserted.
6. Push and hold the button of the One Touch™ Comfort
Control for approximately 60 seconds (3 minutes for
AeroBed Classic Raised
®
) to inflate the
full (firmest) capacity. Bed will not over-inflate.
AeroBed Classic Raised
®
7. If applicable, the
dressed with its valance and cover whilst it is still partially
inflated.
8. Attach the One Touch™ Comfort Control block to the
inflator by sliding it over the rubber nipple.
9. Lie on the bed to adjust the firmness to your desired level.
a. To make the bed softer, depress the One Touch™
Comfort Control block (not the button) and rubber
nipple together.
b. To make the bed firmer, depress only the button of
the One Touch™ Comfort Control.
Close Valve Using 2
Thumbs.
60 sec
AeroBed
®
to
should be
2
DEFLATION AND STORAGE
1. Make sure the bed is unplugged from the electric outlet
prior to deflation.
2. Open the Quick Air Release Valve at the foot of the bed to
release the air in approximately 15 seconds (1 minute for
AeroBed Classic Raised
®
the
3. Roll or fold the AC cord with One Touch™ Comfort Control
block and secure it. Fold sides of bed into the centre
along its length. Tightly roll your
pump towards the Air Release Valve end. When the bed is
completely rolled, and all air is expelled, push the Air
Release Valve closed until it locks.
4. Slide the duffel bag over your
AeroBed
®
in a clean dry place at room temperature (above
50°F/10° C). Storing your
and over 100° F (38° C) may affect its performance and
will not be covered under guarantee.
5. If a mattress cover and/or valance is included with your bed, it/they may be
removed after deflation. Alternatively, you may store your product with the
mattress cover and/or valance on the bed. Wrinkling may occur.

CARE AND MAINTENANCE

AeroBed
1. Inspect your
AeroBed
2. Keep your
be repairable and will not be covered by your guarantee.
3. When not in use, store your
of extreme temperatures. Product must be at room temperature prior to inflating.
AeroBed
4. Do not store your
cause damage to your
5. In case of incidental damage to your bed, a repair kit has been included. Please
follow repair instructions carefully.
Inflation
Beds
If applicable, we recommend that you do not let the plush surface of your
get wet. Repeated exposure to water or other liquids may cause damage to the
plush surface that will not be covered by your guarantee. Should liquid come in
contact with the plush surface, blot liquid dry and use a damp cloth to remove any
stain. Let surface air dry completely.
You may clean the PVC on your
household cleaner. Do not use strong chemicals or other compounds. Allow your
bed to air dry completely after cleaning and before storing.
Cover/Valance (If included)
The mattress cover and valance (if included) are made of polyester/cotton blended
fabric. Machine wash in warm water wth a mild soap or detergent. Tumble dry on
LOW HEAT. Remove immediately after drying.
).
AeroBed
®
around the
AeroBed
®
. Store your
AeroBed
®
under 50° F (10° C)
®
prior to each use.
®
away from any sharp objects. Large cuts or snags may not
AeroBed
®
in its duffle bag, in a clean, dry place out
®
folded inside sofa beds or roll-aways. This may
AeroBed
®
that will not be covered under your guarantee.
CLEANING
AeroBed
®
with a mild dishwashing detergent or
3
AeroBed
®