Publicidad

Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

Porsche 997 2005-2012
KIT FEATURES
• ISO DIN radio provision with pocket
• ISO DDIN radio provision
• 99-9606G - Painted gray
• 99-9606B - Painted black
KIT COMPONENTS
• A) Radio trim panel • B) Radio brackets • C) Pocket • D) (4) #8 x 3/8"
Phillips pan-head screws • E) (4) Phillips 5mm x 12mm flat-head screws
A
B
WIRING & ANTENNA CONNECTIONS (sold separately)
Wiring Harness: • N/A
Antenna Adapter: • 40-EU10
METRA. The World's best kits.
Installation instructions for part 99-9606
99-9606
C
D
E
metraonline.com
Table of Contents
Dash Disassembly ..................................................2
Kit Assembly
– ISO DIN radio provision with pocket ...................... 3
ISO DDIN radio provision ...................................... 3
TOOLS REQUIRED
• Panel removal tool • Phillips screwdriver
• Torx T-15 screwdriver • Torx T-30 screwdriver
• 5mm Allen wrench
CAUTION!
All accessories, switches, climate controls panels, and
especially air bag indicator lights must be connected before cycling
the ignition. Also, do not remove the factory radio with the key in the
on position, or while the vehicle is running.
© COPYRIGHT 2004-2016 METRA ELECTRONICS CORPORATION

Publicidad

Tabla de contenido
loading

Resumen de contenidos para Metra 99-9606

  • Página 1 Installation instructions for part 99-9606 Table of Contents Porsche 997 2005-2012 99-9606 Dash Disassembly ..........2 Kit Assembly – ISO DIN radio provision with pocket ...... 3 KIT FEATURES • ISO DIN radio provision with pocket – ISO DDIN radio provision ........3 •...
  • Página 2: Dash Disassembly

    99-9606 Dash Disassembly 1. Remove the (1) T-30 Torx screw from each of the small carpeted panels under the dash, at the front of the center console on each side. (Figure A) 2. Remove the (2) T-15 Torx screws from the left and right dash side trim panels, then unsnap and remove the panels.
  • Página 3: Kit Assembly

    (4) 5mm x 12mm to the radio. Metra recommends Phillips flat-head screws have using the proper mating adapter from Metra and/or AXXESS. Test the radio been supplied if the radio does not for proper operation . supply these type of screws.
  • Página 4: Important

    Installation instructions for part 99-9606 IMPORTANT If you are having difficulties with the installation of this product, please call our Tech Support line at 1-800-253-TECH. Before doing so, look over the instructions a second time, and make sure the installation was performed exactly as the instructions are stated.
  • Página 5: Componentes Del Kit

    Instrucciones de instalación para la pieza 99-9606 Porsche 997 2005-2012 Indice 99-9606 Desmontaje del tablero ..........2 Ensamble del kit KIT FEATURES – Provisión de radio ISO DIN con cavidad ....3 • Provisión de radio ISO DIN con cavidad –...
  • Página 6: Desmontaje Del Tablero

    99-9606 Desmontaje del tablero 1. Quite el (1) tornillo Torx T-30 de cada uno de los paneles alfombrados pequeños abajo del tablero, en el frente de la consola central de cada lado . (Figura A) 2. Quite los (2) tornillos Torx T-15 del...
  • Página 7: Ensamble Del Kit

    3. Inserte a presión el radio en el que use adaptadores adecuados de tablero, luego inserte a presión el acoplamiento de Metra y/o de AXXESS. panel de la moldura del radio sobre Pruebe el radio para verificar que el radio, y después vuelva a armar el funcione correctamente.
  • Página 8: Importante

    Instrucciones de instalación para la pieza 99-9606 IMPORTANTE Si tiene dificultades con la instalación de este producto, llame a nuestra línea de soporte técnico al 1-800-253-TECH. Antes de hacerlo, revise las instrucciones por segunda vez y asegúrese de que la instalación se haya realizado exactamente...

Tabla de contenido