Putting Into Operation - Asv 7-A; Maintenance And Service - Asv 7-A; Putting Into Operation - As 7; Maintenance - As 7 - Narex ASV 7-SET Instrucciones De Uso

Warning!!
The charger is not user serviceable. There are no user serviceable
parts inside the charger. Servicing at the closest Authorized Ser-
vice Center is required to avoid damage to static sensitive internal
components.
Always use correct battery pack (pack supplied with the tool or the
replacement pack recommended by the manufacturer, the compa-
ny Narex s.r.o.) Never install another battery pack type. It will ruin
your tool and may create a hazardous condition.

Putting into operation - ASV 7-A

Insert the charged battery pack (1) into the cordless screwdriver
battery pack compartment as far as the stop. (Click of the engaged
clamps can be heard (2)). When taking the battery pack (1) out of
the cordless screwdriver, press the clamps (2) on both sides of the
battery pack and then take the battery pack out of the cordless
screwdriver battery pack compartment.
Switching-on
By depressing the operating push button switch (3) and by its
holding you can control speed smoothly. When depressing the
push button switch (3) the LED indicator, serving for lighting the
workplace in front of the tool lamped in the chuck, will go on au-
tomatically.
Switching-off
By releasing the push button switch (3). Runout of the spindle
(chuck) is reduced by the activated brake.
Lower speed is suitable for guiding the bolt/screw into the mate-
rial. Higher speed is suitable for screwing the bolt/screw into the
material.
Attention!
Long-time use of variable rotating speed is not recommended as
its can result in operating push button damage.
Changed direction of rotation
Direction of rotation is changed by the change over switch of the
sense of rotation (4):
· By pushing from the right to the left – right run.
· By pushing from the left to the right – left run.
· Push button in the interposition – protection from uninten-
tional switching.
Attention!
If you wish to change position of the change over switch, check at
first that the operating push button is released.
Note:
During first use of the device and during the first change of the
sense of rotation a loud click can be heard. It is a normal phenome-
non which cannot be considered any problem.
Torque setting
The necessary torque can be set by swiveling the adjusting ring (5)
towards the relevant symbol.
Screwing
Symbol 1
= min. torque
Symbol 5 = max. torque for screwing
Drilling
Symbol = max. torque
Tool clamping and releasing
By swiveling the clamping chuck sleeve (6), you open and close
the clamping jaws, which the working tool (drill, bit holder, etc.) is
inserted into. The devices are equipped by automatic spindle arrest
(locking), facilitating tool replacement, by using one hand only in
the requested direction.

Maintenance and service - ASV 7-A

Instructions for device cleaning
Start the motor and blow impurities and dust out of the vent holes
of the device. Use protective goggles for this operation. Clean the
external plastic parts by a wet rag and mild detergent. Though
these parts are made of the materials resistant to solvents, NEVER
use any solvent.
Instructions for cleaning the charger
Attention! Risk of electric shock. Prior to start han-
dling the charger, disconnect the line plug from the
socket!
Impurities and dust can be removed from external charger surfaces
by a rag or a non-metal brush. Use neither water nor detergents.
Attention! With respect to protection from el. shock
and preservation of the class of protection, all mainte-
nance and service operations requesting jig saw case
removal must be performed by the authorized service centre
only!
The current list of authorized service centres can be found at our
website www.narex.cz, section "Service centres".

Putting into operation - AS 7

Insert the charged battery pack (1) into the rechargeable flashlight
battery pack compartment as far as the stop. (Click of the engaged
clamps can be heard (2). When taking the battery pack (1) out of
the rechargeable flashlight, press the clamps (2) on both sides
of the battery pack and then take the battery pack out of the re-
chargeable flashlight pack compartment.
By depressing the push button switch (11) the flashlight will go on.
By repeated push button depressing (11) the flashlight will go off.
Attention!
LED with a high light intensity is used as the light source. Avoid
direct sight into the light source - this is applicable to yourselves
as well as to other persons (and/or animals) in your close vicinity.
The risk of dazzling and thus injury of the dazzled person (and/or
dazzled animal) is imminent.
The flashlight reflector (12) can be tilted within the range of 0° to
90°, in 30° steps.

Maintenance - AS 7

Instructions for flashlight cleaning
Clean the external plastic parts by a wet rag and mild detergent.
Though these parts are made of the materials resistant to solvents,
NEVER use any solvent.

Accessories

The accessories recommended for use with this device are availa-
ble commercially in the shops with hand el. tools.

Storage

Packed appliance may be stored in dry, unheated storage place
with temperature not lower than -5 °C.
Unpacked appliance should be stored only in dry storage place
with temperature not lower than +5 °C with exclusion of all sudden
temperature changes.

Environmental protection

Power tools, accessories and packaging should be sorted for envi-
ronmental-friendly recy.
Only for EU countries:
Do not dispose of power tools into household waste!
According to the European Directive 2002/96/EC on waste electri-
cal and electronic equipment and its incorporation into national
law, power tools that are no longer suitable for must be separately
collected and sent for recovery in an environmental-friendly man-
ner.
English
19