JUNO REMODEL Instalación

REMODEL RECESSED HOUSING INSTALLATION
WARNING: For your safety, read and understand instructions completely before starting installation. Before wiring to power supply, turn off
electricity at the fuse or circuit breaker box.
NOTE: Juno recessed fixtures are designed to meet the latest NEC and CEC requirements and are listed in full compliance with UL1598 and
CSA #250. Before attempting installation of any recessed lighting fixture, check your local electrical building code. This code sets the wiring
and installation requirements for your locality and should be understood before starting your work.
NOTE: Use of Non-Juno trims voids Juno warranty. Ballast is replaceable from below ceiling by a qualified electrician.
TYPE TC & PL for Non-Insulated Ceilings
Figure 1
Juno Type TC & PL fixtures are designed for
installations where housing and J-Box will not
come into contact with insulation. Insulation
must be spaced 3" away from the housing
and J-Box (Fig. 1)*. Blinking light after instal-
lation indicates that improper lamp or trim is
being used or that fixture has been improp-
erly covered with insulation.
TYPE IC for Insulated Ceilings
Figure 2
Juno Type IC fixtures are designed for direct
contact with insulating materials which are
approved for this application (Fig. 2). Blinking
light after installation indicates that improper
lamp or trim is being used.
Use Juno Air-Loc Gaskets or Air-Loc Rated
Trims with Juno IC housings for additional
energy savings and to comply with
Washington State and other energy codes.
*In Canada, when insulation is present, Type IC fixtures
must be used.
Hg Mark means lamp contains
mercury. Follow disposal laws.
See www.lamprecycle.org
1300 South Wolf Road
© Juno Lighting, LLC. 2012
3"
Step 1. Locate center of proposed opening
on ceiling and use template to mark and
accurately cut a 4-3/8" (for 4" housings),
5-1/2" (for 5" housings) or a 6-3/4" (for
6" housings) opening. For sloped ceiling
housings, an oval hole template is pro-
vided. (Fig. 3).
Step 2. Follow steps 1-4 under electrical
connection.
Step 3. Insert housing through ceiling
opening so it is flush to ceiling (Fig. 4).
Push retention clips outwards until each
clip tab clicks into position.* On some
housings, a single "T" slot clip is provided
for additional support. Insert clip through
"T" slot from inside housing, force clip
down with screwdriver until clip is seated.
Secure clip by tightening screw. (Fig. 5).
*(Note: To remove housing from ceiling, push
tab on clip upward to disengage)
Step 4. Install trim using coil, torsion or leaf
springs as provided. Remove socket paint
protector cover and install proper lamp
(light bulb) as listed on housing label.
Figure 4
P5132
Des Plaines, IL 60018
Printed in USA Rev. 8/12
Installation Steps
Figure 3
.
Figure 5
(847) 827-9880
Electrical Connection Instructions
Figure 6
Step 1. Provide electrical service accord-
ing to your local electrical code to the wir-
ing box located on the remodel housing.
Supply wire insulation must be rated for at
least 90°C.
Step 2. Remove wiring box cover. Remove
the appropriate knock-out to connect
flexible metal conduit or non-metallic cable
to wiring box with proper connectors (by
others) (Fig. 6).
Step 3. Connect supply wires to fixture
wires with proper size wire nuts (not sup-
plied), so as to cover all bare current-
carrying conductors. Connect black fixture
wire to hot, white fixture wire to neutral and
green fixture wire to ground.
Step 4. Place all wiring and connections
back in wiring box and replace cover.
PRODUCT GUARANTEE: Juno warrants to the
first non-retail purchaser of any of its products
that its products are free from defects in mate-
rial and workmanship. In the event of any defect,
Juno's sole obligation is expressly limited to repair
or replacement, without charge, at Juno's factory
after prior written return authorization has been
granted. In no event shall Juno's obligation under
this Warranty extend beyond the initial cost of the
product and accordingly, any consequential dam-
ages arising out of a defect therein are expressly
excluded. This Warranty shall not apply to prod-
ucts which have been altered, improperly used or
repaired outside of Juno's factory nor shall it apply
to defects for which written notice thereof is not
received by Juno within two (2) year from the date
of purchase.
THIS WARRANTY IS IN LIEU OF ALL OTHER
WARRANTIES, EXPRESSED OR IMPLIED, AND
WITHOUT EXCLUDING THE GENERALITY OF THE
FOREGOING, EXCLUDES ANY IMPLIED WARRANTY
OF MERCHANTABILITY. SPECIFICATIONS SUBJECT TO
CHANGE WITHOUT NOTICE.
www.junolightinggroup.com