Technical Data; Noise/Vibration Information; Declaration Of Conformity - Bosch AXT 22 D Manual Original

14 | English

Technical Data

Quiet-shredder
Article number
Power consumption, S 6
1)
(40/60 s)
Power consumption, S 1
No-load speed
Cutting system
Capacity, max.
Branch diameter, max.
Collection box
Weight according to
EPTA-Procedure 01/2003
Protection class
1)
The S 6 operating mode (40 %) indicates a load profile of 40 s load and 60 s idle time. For practical applica-
tion, continuous operation is permitted.
2)
Depending on the hardness of the wood.
Starting cycles generate brief voltage drops. Interference with other equipment/machines may occur in case of
unfavourable mains system conditions. Malfunctions are not to be expected for system impedances below
0.36 ohm.

Noise/Vibration Information

Measured sound values determined according to 2000/14/EC
(1.60 m height, 1 m distance away).
Typically the A-weighted noise levels of the product are:
Sound pressure level
Sound power level
Uncertainty K
Wear hearing protection!

Declaration of Conformity

We declare under our sole responsibility that the product de-
scribed under "Technical data" is in conformity with the following
standards or standardization documents: EN 60335, EN 13683 ac-
cording to the provisions of the directives 2004/108/EC,
2006/42/EC, 2000/14/EC.
2000/14/EC: Guaranteed sound power level
Conformity assessment procedure according to Annex V.
Equipment category: 50
Technical file at:
Bosch Lawn and Garden Ltd., PT-LG/EAE,
Stowmarket, Suffolk IP14 1EY, England
Dr. Egbert Schneider
Senior Vice President
Engineering
Robert Bosch GmbH, Power Tools Division
D-70745 Leinfelden-Echterdingen
24.02.2011
Assembly
For Your Safety
Warning! Switch off, remove plug from
mains before adjusting, cleaning or if ca-
ble is cut, damaged or entangled.
F 016 L70 735 | (11.4.11)
3 600 ...
W
W
-1
min
kg/h
mm
l
kg
Dr. Eckerhard Strötgen
Head of Product
Certification
AXT 22 D AXT 25 D
H03 0.. H03 1..
2200 2500
2000 2300
40
Drum Drum
2)
180 190
2)
38 40
53
31.3 31.3
/I
Observe correct mains voltage: The voltage
of the power source must agree with the volt-
age specified on the nameplate of the unit.
Equipment marked with 230 V can also be
connected to 220 V or 240 V.
The circuit must at least be protected as fol-
lows:
AXT 22 D/25 D/23 TC/25 TC = 13 A
An extension cable with a cross section that is
too small causes a distinct reduction in the
performance capabilities of the machine. For
cables to 25 m in length, a cross section of at
least 3 x 1.5 mm
than 25 m in length, the cross section must be
at least 2.5 mm
WARNING! Inadequate extension cables
can be dangerous. Extension cable, plug
and socket must be of watertight con-
struction and intended for outdoor use.
Cable connections should be kept dry and off
the ground.
AXT 23 TC AXT 25 TC
H03 2..
2300
2100
40 40
Turbine
2) 2)
215
2) 2)
42
53 53
30.5
/I /I
3 600 ... H03 0..
H03 1..
dB(A) 81
dB(A) 89
dB =3
3 600 ... H03 0..
H03 1..
dB(A) 92
2
is required, for cables more
2
.
Bosch Power Tools
H03 3..
2500
2300
40
Turbine
2)
230
2)
45
53
30.5
/I
H03 2..
H03 3..
82
90
=2
H03 2..
H03 3..
92