Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
Hot air gun features four position switch (3) and allows to adjust
temperature and air flow parameters according to the needs for
work at hand (fig. B). Set the switch to appropriate position.
Position 0 – switched off
Position I – temperature - 25
C
0
Position II – temperature range - 80 - 600
Position III – temperature range - 80 - 600
Position I is used to cool down hot objects, drying paint or cooling
the device after long operation with high temperature before
putting it away or replacing a nozzle.
When changing high temperature position II or III to position I, wait
until the device cools down to temperature of 25
Hot air gun is very easy to use. Four position switch (3) allows to
adjust air stream temperature to the work at hand. Wait for a while
after switching the hot air gun on to allow stream of air to reach
desired temperature.
Small emission of smoke is normal when switching the hot air gun
for the first time.
PROTECTION AGAINST OVERHEATING
Do not put hot air gun nozzle too close to processed material, as
it could cause reflection of hot air stream from the surface and
activation of overheating protection.
Choose distance between nozzle and processed object depending
on its material and additional nozzle being used. Determine the
most suitable temperature by trials and errors, therefore start
operation at low temperature range.
In case of overheating (thermal overloading), when thermal
protection activates, heaters inside hot air gun are switched off
automatically, but blower continues to operate. When the tool
cools down to working temperature setting, heating will be
switched on automatically.
SHAPING PLASTIC PIPES / DEFROSTING
• Put reflector nozzle onto outlet nozzle. Avoid narrowing the pipe
by filling it with sand and sealing at both sides.
• Heat the pipe by moving it over the hot air gun.
• Always heat frozen water system pipes starting from ends towards
middle point. To avoid damages, be very careful when heating
plastic pipes and connections between pipes.
Often it is impossible to differ water system pipes from gas
pipes. Be very careful. You must not heat gas pipes under any
circumstances.
PRIOR TO OPERATION
Work place
1.
Ensure there are no objects nearby that limit free movement,
comfortable and safe use of the tool.
Power supply
2.
Ensure the specification of power supply that the hot air gun is to be
connected to matches requirements described on the rating plate
of the tool.
Switch
3.
Ensure the switch is in the off position. When plugging to power
supply socket when the switch is in the ON position, immediate start
of hot air gun operation may cause a serious accident.
Extension cord
4.
When the workplace is far away from the power supply socket use
extension cord with appropriate cross section, matched to current
used. Use the shortest possible extension cord.
Operation check
5.
Operation of hot air gun should be smooth and even. Use such tool
only.
REMOVING PAINT
• Switch hot air gun and set appropriate working temperature.
C
0
C
0
C.
0
10
• Direct the hot air stream to surface coated with paint. Bubbles will
appear after some time. Do not allow burning of paint, it would
make removal more difficult.
• When removing paint with scraper or putty knife, remove it
gradually from top to bottom. If you encounter a place where
the paint cannot be removed, carefully put the hot air gun closer
to aid you in your work. Clean the putty knife blade from time to
time.
• Remove paint before it hardens, otherwise it will adhere to the
knife blade.
• After the work is finished, quickly remove remaining of paint with
wire brush before it hardens.
Just after the operation is finished, the nozzle will be hot. Avoid
direct contact and use appropriate protective gloves, or wait until
it cools down.
Do not use plastic knives to remove paint heated with the hot air
gun.
OPERATION AND MAINTENANCE
Unplug the power cord from mains socket before commencing
any activities related to installation, adjustment, repair or
maintenance.
• Keep the hot air gun clean and ensure free air flow.
• Protect the hot air gun against water.
• Do not clean the hot air gun with water or chemical cleaning
agents.
• Use soft cloth for cleaning the body.
• Store the hot air gun in a dry place, beyond reach of children.
• Entrust replacement of power cord and other repairs only to
qualified persons, use only original parts.
All faults should be repaired by service workshop authorized by the
manufacturer.
TECHNICAL PARAMETERS
RATED PARAMETERS
Hot Air Gun
Parameter
Supply voltage
Current frequency
Rated power
gear I
Temperature
gear II
gear III
gear I
Air flow
gear II
gear III
Protection class
Protection against overheating (thermal
switch)
Weight
Year of production
ENVIRONMENTAL PROTECTION
Electrical equipment must not be disposed off with household
waste and, instead, should be utilized at appropriate facilities.
Information on utilization can be provided by the product
vendor or the local authorities. Waste electrical and electronic
equipment contains substances that are not neutral to
the natural environment. Equipment that is not recycled
constitutes a potential hazard to the environment and to
human health.
* Right to introduce changes is reserved.
Value
230 V AC
50 Hz
2000 W
25
C
0
80 - 600
C
0
80 - 600
C
0
350 l/min
350 l/min
550 l/min
II
yes
0,9 kg
2020
Publicidad
Tabla de contenido
