Toya POWER UP 79237 Manual De Instrucciones página 11

GB
closed areas. Using a correct extension cord permits to reduce the risk of an electric shock.
If operating a power toll in damp location is unavoidable, use a residual current device (RCD) protected supply. Use of
an RCD reduces the risk of electric shock
Personal safety
Commence work in good physical and psychological conditions. Pay attention to what you do. Do not work if you are
tired or under effects of medicines or alcohol. Even a moment's inattention during work may lead to serious injuries.
Always use individual means of protection. Always wear goggles. Using individual means of protection, such as dust-masks,
protective shoes, helmets and hearing protections permits to reduce the risk of serious injuries.
Avoid accidental activation of the tool. Make sure the switch is in the OFF position, before you connect the tool to the
mains. Holding the tool with a finger on the switch or connecting an electric tool when the switch is in the ON position may lead
to serious injuries.
Before you turn an electric tool on remove all the spanners and other tools, which have been used for adjustments. A
spanner left on rotating elements of the tool may lead to serious injuries.
Keep your balance. Maintain an appropriate position. It will permit to control the electric tool in case of unpredicted situations
during its operation.
Use protective clothes. Do not wear loose clothes or jewellery. Keep your hair, clothes and gloves away from moving
elements of the electric tool. Loose clothes, jewellery or long hair may get caught on moving elements of the tool.
Use dust extractors or dust containers, if the tool is equipped with any. Make sure they are properly connected. Using of
dust extractors permits to reduce the risk of serious injuries.
Operation of the electric tool
Do not overload the electric tool. Use a proper tool for the given purpose. A correct selection of the tool for the given work
will result in a more efficient and safer work.
Do not use the electric tool if the switch is not functioning properly. A tool which may not be controlled by means of a switch
is dangerous and must be repaired.
Disconnect the plug from the mains socket before any adjustment, replacement of accessories or storage of the tool. It
will permit to avoid accidental activation of the electric tool.
Store the tool away from children. Do not allow untrained persons to operate the tool. An electric tool may be dangerous
in hands of an untrained person.
Make sure the tool is properly maintained. Check the tool in order to detects any unfitting or loose moving elements.
Check whether the elements of the tool are not damaged. In case any damaged elements of the tool are detected, they
must be repaired before the electric tool is operated. Many accidents are caused by improper maintenance of tools.
Cutting tools must be sharp and clean. Properly maintained cutting tools are easier to control during work.
Use electric tools and accessories in accordance with the aforementioned instructions. Use the tool in accordance with
its purpose, taking into account the kind and conditions of work. Should the tool be used for other applications than the ones
it has been designed for, the risk of a dangerous situation increases.
Repairs
The tool may be repaired only by authorised service centres, which must use solely original spare parts. It will guarantee
a proper level of safety of operation of the electric tool.
OPERATION OF THE TOOL
Installation of the insertion tool
Attention! The actions described in this point must be realised when the power supply is off. Remove the plug of the cord of the
tool from the socket!
While installing insertion tools with sharp edges, be careful and use personal protection equipment, particularly protective
gloves.
Use a wrench to remove the fixing bolt, remove the washer and the clamping ring (II). Install the insertion tool designed for the
given kind of work. Install the insertion tool on the spindle holder in a manner that facilitates the job and at the same time guar-
antees its safety.
Attention! It is prohibited to carry out the installation procedure where the working section of the insertion tool (the blade) is
directed towards the operator of the tool.
Make sure the holes of the insertion tool are aligned with the pins of the spindle holder (III). Attention! It is prohibited to carry out
the installation procedure where the insertion tool is fixed with fewer than two pins.
Attention! It is recommended to install insertion tools with closed clamping system. It is acceptable to use insertion tools with an
open clamping system, but in such a case make sure there are no free pins on the spindle holder.
Install the clamping ring, the washer and then screw the fixing bolt down tightly and safely (IV).
O R I G I N A L I N S T R U C T I O N S
11