Installation; Commissioning; Teaching In The Door Operator; Teaching In With A Remote Transmitter - Cardo Magic 600 Manual De Instrucciones

the door type that is being attached and/or install it according
to the relevant manual.

13 Installation

See instructions for installation on page ff 155.
The head of the operator can be turned by 90° to the running
rail respectively as required (see page 155 (A)).
Installation step D, page 156:
1. Tighten the toothed belt's clamping nut until the toothed
belt no longer rests on the guide rail (equivalent to
dimension X).
2. Use the clamping nut (dimension B) to increase the
toothed belt tension to correspond to the length of the door
operator.

14 Commissioning

Once installation is complete
• Slowly open the door by hand until you hear the slide snap
in.
• Make connection to mains, display flashes alternately with
L and 4. The door operator lamp flashes in intervals of 4.
• Teach in the door operator (see Chapter 15).
• Teach in the remote transmitter (see Chapter 16).
• Carry out a safety inspection (see Chapter 9).

15 Teaching in the door operator

ATTENTION: No protection is provided by the load
switch-off whilst the door operator is being taught
in.
Note: Teaching in is only possible during initial installation or
after resetting the door operator. Do not press any keys
during the teach-in procedure.
Preparation: Connect the door to the door operator.

Teaching in with a remote transmitter

At the time of delivery and after resetting the door
operator, the remote transmitter supports the following
functions:
• A Safety control operation and fine adjustment "OPEN"
• B Safety control operation and fine adjustment "CLOSE"
• C and D Confirmation (storage)
Once the door operator has been taught
in, key A is used for remote control and
the other keys can be used to control
other similar door operators or other
radio receivers.
Teaching in
• Press and hold down key A; the door
moves in the open direction.
• When you reach the desired end position "OPEN", release
key A. (You can make corrections with key B.)
• Press key C once briefly, teach-in procedure: The door
operator automatically stores "End position OPEN/CLOSE"
and the loads of the "Travel path OPEN/CLOSE". The door
operator lights flash in synchronism.
Teach-in is complete when the door is open and the door
operator lights are on.
Check load switch-off according to Chapter 9,Safety
inspection.

Teaching in without a remote transmitter

On the door operator:
10 / 208
• Press and hold pushbutton
open direction. Release pushbutton when the desired
opening position is reached. A correction can be made with
the pushbutton
• Press the Menu pushbutton
automatically stores "End position OPEN/CLOSE" and the
loads of the "Travel path OPEN/CLOSE" . The door
operator lights flash in synchronism.
Teach-in is complete when the door is open and the door
operator lights are on.
Check load switch-off according to Chapter 9,Safety
inspection.
16 Teaching in/deleting a remote
transmitter
Programming the remote transmitter:
• During one of the 3 status messages A, B or C (seeChapter
10), press the pushbuttons
(approx. 1 s), F flashes in the display.
• Press the desired key on the remote transmitter, the radio
command is taught in. F appears in the display.
Note: F appears in the display during the transmission pulse.
Deleting (all) remote transmitter(s):
During one of the 3 status messages A, B or C (see Chapter
10), press the pushbuttons
seconds, F flashes in the display. The status message
reappears after 3 seconds.

17 Operation

CAUTION: Mishandling the product can result in
injuries or material damage. Follow the basic safety
rules:
When opening or closing the door, do not block the interior or
exterior swivel ranges. Keep children away.
The door movements can be activated or stopped using the
remote transmitter provided or via switching elements such
as the wall keypad, which can be connected if desired.
Optional external features (such as the EMERGENCY STOP)
can also be connected to the door operator.
The operator must be connected to a door before
it is used. If it is not, incorrect load values will be
taught in to the electronic system. This can cause
malfunctions.

18 Programming

Switch on programming mode
During one of the 3 status messages A, B or C (seeChapter
10) press the Menu pusbutton
seconds. The display changes to the menu (D).
Select programming menu
Select the desired menu with the pushbuttons
2-character menu name flashes on and off. The following
appears for menu A0: A 0 A...
Show / change menu value
Displays: Press the Menu pushbutton
seconds, the menu value (E) is displayed.
Change: Change the value with the pushbuttons
Save: Press the Menu pushbutton
seconds, the programming menu (D) is displayed.
N000924 12/2010
and the door moves in the
.
The door operator
and simultaneously
and simultaneously for >6
for longer than 1.5
for less than 1.5
for less than 1.5
and . The
and .
Magic 600