Product Familiarisation; Fitting Accessories - Silverline 127655 Manual Del Usuario

GB

Product Familiarisation

1 Outlet nozzle
2 Inlet vents
3 On/Off switch
4 Accessory nozzles
Unpacking and Assembling your
Hot Air Gun
• Carefully unpack and inspect the hot air gun. Fully familiarise yourself
with all features and functions of the tool.
• If any parts are damaged or missing, have these parts repaired or
replaced before use.

Fitting Accessories

NOTE: Always ensure that the hot air gun is unplugged, and fully cooled
before attempting to fit accessories.
• The accessory nozzles (4) supplied, allow the hot air gun to be used for a
variety of different tasks.
• Accessories are a push fit onto the outlet nozzle (1).
Operating Instructions
• Always hold the machine by the handle provided.
• Do not obscure the inlet vents (2).
• Always wear appropriate personal protective equipment for the job that
you are to do. Use of this machine requires ear defenders, safety goggles,
gloves, and a breathing mask.
Switching on
• The outlet has two preset temperatures. This can be adjusted by
changing the position of the on/off switch (3).
• For the lower setting (300ºC) move the switch into the "I" position.
• For the higher setting (600ºC) move the switch into the "II" position.
• To turn the hot air gun off move the on/off switch to the "O" position.
• Be aware that the metal parts of the tool will remain hot for some time
after switching off. Allow at least 30mins for the gun to cool before
leaving unattended.
Paint stripping
• Connect the tool to the mains supply, and switch on.
• Direct the hot air onto the paint to be removed, keeping the nozzle at
least 25mm away from the surface.
NOTE: Take extra care when removing paint from window frames.
The heat from this tool can cause damage to glass if used carelessly.
• Allow the paint to soften, and remove using a suitable scraper.
• Do not overheat the paint, if you notice smoke or blackening, stop
heating.
• Do not allow waste to build up, or drop into the outlet nozzle (1) as it will
be a fire hazard.
Pipe defrosting
• This hot air gun can be used to defrost frozen water pipes.
• Using a suitable attachment, aim hot air at the frozen pipe. Move the hot
air gun along the pipe so that the whole length defrosts evenly.
• Be aware of overheating areas directly behind the pipe being defrosted.
• Do not attempt to defrost PVC pipe as the heat of the air may cause
permanent damage.
Drying
• This hot air gun can be used to dry damp wood or other materials.
• Be very careful when operating power tools near damp materials, the
presence of water greatly increases the danger of electric shock.
6
• Always refer to the product manufacturers instructions if using the hot
air gun to dry plaster, paint, or other finishes. Do not use the hot air gun
on any flammable material, or any material than may produce hazardous
fumes.
Stationary use
• This hot air gun can also be used statically, keeping hands free to
manipulate the workpiece.
• The hot air gun is designed to stand upright on a suitable workbench.
The outlet nozzle (1) should point straight upwards. The nozzle must not
contact the workbench, or any other object.
• Ensure that the power cable is well supported, and will not become
caught as you work.
• Switch the hot air gun on, and move workpiece into the hot air flow. Take
care to keep your hands and face away from the hot air.
Maintenance
Cleaning
• Disconnect the machine from the mains supply before cleaning.
• Keep your machine clean. Always clean dust and particles away, and
never allow ventilation holes to become blocked. Do not allow waste to
collect on any part of the tool. Use a soft brush, or dry cloth to clean the
machine, if available blow through the ventilation holes with clean, dry,
compressed air.
Disposal
• Do not dispose of power tools, or other waste electrical and electronic
equipment, with household waste.
• Contact your local waste disposal authority for information on the proper
way to dispose of tools.